Packetizer

RFC 8570 - IS-IS Traffic Engineering (TE) Metric Extensions

(Formats: TXT)

Internet Engineering Task Force (IETF) L. Ginsberg, Ed. Request for Comments: 8570 Cisco Systems, Inc. Obsoletes: 7810 S. Previdi, Ed. Category: Standards Track Huawei ISSN: 2070-1721 S. Giacalone Microsoft D. Ward Cisco Systems, Inc. J. Drake Juniper Networks Q. Wu Huawei March 2019
IS-IS Traffic Engineering (TE) Metric Extensions Abstract In certain networks, such as, but not limited to, financial information networks (e.g., stock market data providers), network- performance criteria (e.g., latency) are becoming as critical to data-path selection as other metrics. This document describes extensions to IS-IS Traffic Engineering Extensions (RFC 5305). These extensions provide a way to distribute and collect network-performance information in a scalable fashion. The information distributed using IS-IS TE Metric Extensions can then be used to make path-selection decisions based on network performance. Note that this document only covers the mechanisms with which network-performance information is distributed. The mechanisms for measuring network performance or acting on that information, once distributed, are outside the scope of this document. This document obsoletes RFC 7810. Ginsberg, et al. Standards Track [Page 1] RFC 8570 IS-IS TE Metric Extensions March 2019 Status of This Memo This is an Internet Standards Track document. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 7841. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at https://www.rfc-editor.org/info/rfc8570. Copyright Notice Copyright (c) 2019 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Ginsberg, et al. Standards Track [Page 2] RFC 8570 IS-IS TE Metric Extensions March 2019 Table of Contents 1. Introduction ....................................................3 1.1. Requirements Language ......................................4 2. TE Metric Extensions to IS-IS ...................................5 3. Interface and Neighbor Addresses ................................6 4. Sub-TLV Details .................................................7 4.1. Unidirectional Link Delay Sub-TLV ..........................7 4.2. Min/Max Unidirectional Link Delay Sub-TLV ..................8 4.3. Unidirectional Delay Variation Sub-TLV .....................9 4.4. Unidirectional Link Loss Sub-TLV ..........................10 4.5. Unidirectional Residual Bandwidth Sub-TLV .................11 4.6. Unidirectional Available Bandwidth Sub-TLV ................12 4.7. Unidirectional Utilized Bandwidth Sub-TLV .................13 5. Announcement Thresholds and Filters ............................13 6. Announcement Suppression .......................................14 7. Network Stability and Announcement Periodicity .................15 8. Enabling and Disabling Sub-TLVs ................................15 9. Static Metric Override .........................................15 10. Compatibility .................................................15 11. Security Considerations .......................................15 12. IANA Considerations ...........................................16 13. References ....................................................17 13.1. Normative References .....................................17 13.2. Informative References ...................................18 Appendix A. Changes from RFC 7810 .................................19 Acknowledgements ..................................................20 Contributors ......................................................20 Authors' Addresses ................................................21 1. Introduction In certain networks, such as, but not limited to, financial information networks (e.g., stock market data providers), network- performance information (e.g., latency) is becoming as critical to data-path selection as other metrics. In these networks, extremely large amounts of money rest on the ability to access market data in "real time" and to predictably make trades faster than the competition. Because of this, using metrics such as hop count or cost as routing metrics is becoming only tangentially important. Rather, it would be beneficial to be able to make path-selection decisions based on performance data (such as latency) in a cost-effective and scalable way. Ginsberg, et al. Standards Track [Page 3] RFC 8570 IS-IS TE Metric Extensions March 2019 This document describes extensions (hereafter called "IS-IS TE Metric Extensions") to the Extended IS Reachability TLV defined in [RFC5305]; these extensions can be used to distribute network- performance information (such as link delay, delay variation, packet loss, residual bandwidth, and available bandwidth). The data distributed by the IS-IS TE Metric Extensions described in this document is meant to be used as part of the operation of the routing protocol (e.g., by replacing cost with latency or considering bandwidth as well as cost), to enhance Constrained Shortest Path First (CSPF), or for other uses such as supplementing the data used by an Application-Layer Traffic Optimization (ALTO) server [RFC7285]. With respect to CSPF, the data distributed by IS-IS TE Metric Extensions can be used to set up, fail over, and fail back data paths using protocols such as RSVP-TE [RFC3209]. Note that the mechanisms described in this document only disseminate performance information. The methods for initially gathering that performance information (such as the methods described in [RFC6375]) or how to act on the information once it is distributed are outside the scope of this document. Example mechanisms to measure latency, delay variation, and loss in an MPLS network are given in [RFC6374]. While this document does not specify how the performance information should be obtained, the measurement of delay SHOULD NOT vary significantly based upon the offered traffic load. Thus, queuing delays SHOULD NOT be included in the delay measurement. For links such as forwarding adjacencies [RFC4206], care must be taken that measurement of the associated delay avoids significant queuing delays; that could be accomplished in a variety of ways, including either (1) measuring with a traffic class that experiences minimal queuing or (2) summing the measured link delays of the components of the link's path. This document obsoletes [RFC7810]. 1.1. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. Ginsberg, et al. Standards Track [Page 4] RFC 8570 IS-IS TE Metric Extensions March 2019 2. TE Metric Extensions to IS-IS This document registers new IS-IS TE sub-TLVs in the "Sub-TLVs for TLVs 22, 23, 141, 222, and 223" registry. These new sub-TLVs provide ways to distribute network-performance information. The extensions in this document build on the extensions provided in IS-IS TE [RFC5305] and GMPLS [RFC4203]. The Extended IS Reachability TLV (type 22) (defined in [RFC5305]), Inter-AS Reachability TLV (also called "inter-AS reachability information TLV") (type 141) (defined in [RFC5316]), and MT-ISN TLV (type 222) (defined in [RFC5120]) have nested sub-TLVs that permit the TLVs to be readily extended. This document registers several sub-TLVs: Type Description ---------------------------------------------------- 33 Unidirectional Link Delay 34 Min/Max Unidirectional Link Delay 35 Unidirectional Delay Variation 36 Unidirectional Link Loss 37 Unidirectional Residual Bandwidth 38 Unidirectional Available Bandwidth 39 Unidirectional Utilized Bandwidth As can be seen in the list above, the sub-TLVs described in this document carry different types of network-performance information. The new sub-TLVs include a bit called the Anomalous (or "A") bit. When the A bit is clear (or when the sub-TLV does not include an A bit), the sub-TLV describes steady-state link performance. This information could conceivably be used to construct a steady-state performance topology for initial tunnel-path computation or to verify alternative failover paths. When network performance violates configurable link-local thresholds, a sub-TLV with the A bit set is advertised. That sub-TLV could be used by the receiving node to determine whether to (1) fail traffic to a backup path or (2) calculate an entirely new path. From an MPLS perspective, the intent of the A bit is to permit label switched path ingress nodes to determine whether the link referenced in the sub-TLV affects any of the label switched paths for which it is ingress. If Ginsberg, et al. Standards Track [Page 5] RFC 8570 IS-IS TE Metric Extensions March 2019 they are affected, then they can determine whether those label switched paths still meet end-to-end performance objectives. If not, then the node could conceivably move affected traffic to a pre-established protection label switched path or establish a new label switched path and place the traffic in it. If link performance then improves beyond a configurable minimum value (reuse threshold), that sub-TLV can be re-advertised with the A bit cleared. In this case, a receiving node can conceivably do whatever re-optimization (or failback) it wishes to do (including nothing). Note that when a sub-TLV does not include the A bit, that sub-TLV cannot be used for failover purposes. The A bit was intentionally omitted from some sub-TLVs to help mitigate oscillations. See Section 5 for more information. Consistent with the existing IS-IS TE specification [RFC5305], the bandwidth advertisements defined in this document MUST be encoded as IEEE floating-point values [IEEE754]. The delay and delay-variation advertisements defined in this document MUST be encoded as integer values. Delay values MUST be quantified in units of microseconds, packet loss MUST be quantified as a percentage of packets sent, and bandwidth MUST be sent as bytes per second. All values (except residual bandwidth) MUST be calculated as rolling averages, where the averaging period MUST be a configurable period of time. See Section 5 for more information. 3. Interface and Neighbor Addresses The use of IS-IS TE Metric Extensions sub-TLVs is not confined to the TE context. In other words, IS-IS TE Metric Extensions sub-TLVs defined in this document can also be used for computing paths in the absence of a TE subsystem. However, as for the TE case, Interface Address and Neighbor Address sub-TLVs (IPv4 or IPv6) MUST be present. The encoding is defined in [RFC5305] for IPv4 and in [RFC6119] for IPv6. Ginsberg, et al. Standards Track [Page 6] RFC 8570 IS-IS TE Metric Extensions March 2019 4. Sub-TLV Details 4.1. Unidirectional Link Delay Sub-TLV This sub-TLV advertises the average link delay between two directly connected IS-IS neighbors. The delay advertised by this sub-TLV MUST be the delay from the local neighbor to the remote neighbor (i.e., the forward-path latency). The format of this sub-TLV is shown in the following diagram: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |A| RESERVED | Delay | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 1 where: Type: 33 Length: 4 A bit: This field represents the Anomalous (A) bit. The A bit is set when the measured value of this parameter exceeds its configured maximum threshold. The A bit is cleared when the measured value falls below its configured reuse threshold. If the A bit is cleared, the sub-TLV represents steady-state link performance. RESERVED: This field is reserved for future use. It MUST be set to 0 when sent and MUST be ignored when received. Delay: This 24-bit field carries the average link delay over a configurable interval in microseconds, encoded as an integer value. When set to the maximum value 16,777,215 (16.777215 seconds), then the delay is at least that value and may be larger. Ginsberg, et al. Standards Track [Page 7] RFC 8570 IS-IS TE Metric Extensions March 2019 4.2. Min/Max Unidirectional Link Delay Sub-TLV This sub-TLV advertises the minimum and maximum delay values between two directly connected IS-IS neighbors. The delay advertised by this sub-TLV MUST be the delay from the local neighbor to the remote neighbor (i.e., the forward-path latency). The format of this sub-TLV is shown in the following diagram: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |A| RESERVED | Min Delay | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | RESERVED | Max Delay | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 2 where: Type: 34 Length: 8 A bit: This field represents the Anomalous (A) bit. The A bit is set when one or more measured values exceed a configured maximum threshold. The A bit is cleared when the measured value falls below its configured reuse threshold. If the A bit is cleared, the sub-TLV represents steady-state link performance. RESERVED: This field is reserved for future use. It MUST be set to 0 when sent and MUST be ignored when received. Min Delay: This 24-bit field carries the minimum measured link delay value (in microseconds) over a configurable interval, encoded as an integer value. Max Delay: This 24-bit field carries the maximum measured link delay value (in microseconds) over a configurable interval, encoded as an integer value. Implementations MAY also permit the configuration of an offset value (in microseconds) to be added to the measured delay value, to facilitate the communication of operator-specific delay constraints. Ginsberg, et al. Standards Track [Page 8] RFC 8570 IS-IS TE Metric Extensions March 2019 It is possible for Min Delay and Max Delay to be the same value. When the delay value (Min Delay or Max Delay) is set to the maximum value 16,777,215 (16.777215 seconds), then the delay is at least that value and may be larger. 4.3. Unidirectional Delay Variation Sub-TLV This sub-TLV advertises the average link delay variation between two directly connected IS-IS neighbors. The delay variation advertised by this sub-TLV MUST be the delay from the local neighbor to the remote neighbor (i.e., the forward-path latency). The format of this sub-TLV is shown in the following diagram: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | RESERVED | Delay Variation | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 3 where: Type: 35 Length: 4 RESERVED: This field is reserved for future use. It MUST be set to 0 when sent and MUST be ignored when received. Delay Variation: This 24-bit field carries the average link delay variation over a configurable interval in microseconds, encoded as an integer value. When set to 0, it has not been measured. When set to the maximum value 16,777,215 (16.777215 seconds), then the delay is at least that value and may be larger. Ginsberg, et al. Standards Track [Page 9] RFC 8570 IS-IS TE Metric Extensions March 2019 4.4. Unidirectional Link Loss Sub-TLV This sub-TLV advertises the loss (as a packet percentage) between two directly connected IS-IS neighbors. The link loss advertised by this sub-TLV MUST be the packet loss from the local neighbor to the remote neighbor (i.e., the forward-path loss). The format of this sub-TLV is shown in the following diagram: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |A| RESERVED | Link Loss | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 4 where: Type: 36 Length: 4 A bit: This field represents the Anomalous (A) bit. The A bit is set when the measured value of this parameter exceeds its configured maximum threshold. The A bit is cleared when the measured value falls below its configured reuse threshold. If the A bit is cleared, the sub-TLV represents steady-state link performance. RESERVED: This field is reserved for future use. It MUST be set to 0 when sent and MUST be ignored when received. Link Loss: This 24-bit field carries link packet loss as a percentage of the total traffic sent over a configurable interval. The basic unit is 0.000003%, where (2^24 - 2) is 50.331642%. This value is the highest packet-loss percentage that can be expressed (the assumptions being that (1) precision is more important on high-speed links than the ability to advertise loss rates greater than this and (2) high-speed links with over 50% loss are unusable). Therefore, measured values that are larger than the field maximum SHOULD be encoded as the maximum value. Ginsberg, et al. Standards Track [Page 10] RFC 8570 IS-IS TE Metric Extensions March 2019 4.5. Unidirectional Residual Bandwidth Sub-TLV This sub-TLV advertises the residual bandwidth between two directly connected IS-IS neighbors. The residual bandwidth advertised by this sub-TLV MUST be the residual bandwidth from the system originating the Link State Advertisement (LSA) to its neighbor. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Residual Bandwidth | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 5 where: Type: 37 Length: 4 Residual Bandwidth: This field carries the residual bandwidth on a link, forwarding adjacency [RFC4206], or bundled link in IEEE floating-point format with units of bytes per second. For a link or forwarding adjacency, residual bandwidth is defined to be the maximum bandwidth [RFC5305] minus the bandwidth currently allocated to RSVP-TE label switched paths. For a bundled link, residual bandwidth is defined to be the sum of the component link residual bandwidths. The calculation of residual bandwidth is different than that of unreserved bandwidth [RFC5305]. This calculation subtracts tunnel reservations from maximum bandwidth (i.e., the link capacity) [RFC5305] and provides an aggregated remainder across priorities. Unreserved bandwidth, on the other hand, is subtracted from the maximum reservable bandwidth (the bandwidth that can theoretically be reserved) and provides per-priority remainders. Residual bandwidth and unreserved bandwidth [RFC5305] can be used concurrently, and each has a separate use case (e.g., the former can be used for applications like Weighted ECMP, while the latter can be used for call admission control). Ginsberg, et al. Standards Track [Page 11] RFC 8570 IS-IS TE Metric Extensions March 2019 4.6. Unidirectional Available Bandwidth Sub-TLV This sub-TLV advertises the available bandwidth between two directly connected IS-IS neighbors. The available bandwidth advertised by this sub-TLV MUST be the available bandwidth from the system originating this sub-TLV. The format of this sub-TLV is shown in the following diagram: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Available Bandwidth | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 6 where: Type: 38 Length: 4 Available Bandwidth: This field carries the available bandwidth on a link, forwarding adjacency, or bundled link in IEEE floating-point format with units of bytes per second. For a link or forwarding adjacency, available bandwidth is defined to be residual bandwidth (see Section 4.5) minus the measured bandwidth used for the actual forwarding of non-RSVP-TE label switched path packets. For a bundled link, available bandwidth is defined to be the sum of the component link available bandwidths. Ginsberg, et al. Standards Track [Page 12] RFC 8570 IS-IS TE Metric Extensions March 2019 4.7. Unidirectional Utilized Bandwidth Sub-TLV This sub-TLV advertises the bandwidth utilization between two directly connected IS-IS neighbors. The bandwidth utilization advertised by this sub-TLV MUST be the bandwidth from the system originating this sub-TLV. The format of this sub-TLV is shown in the following diagram: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Utilized Bandwidth | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 7 where: Type: 39 Length: 4 Utilized Bandwidth: This field carries the bandwidth utilization on a link, forwarding adjacency, or bundled link in IEEE floating-point format with units of bytes per second. For a link or forwarding adjacency, bandwidth utilization represents the actual utilization of the link (i.e., as measured by the advertising node). For a bundled link, bandwidth utilization is defined to be the sum of the component link bandwidth utilizations. 5. Announcement Thresholds and Filters The values advertised in all sub-TLVs (except minimum/maximum delay and residual bandwidth) MUST represent an average over a period of time or be obtained by a filter that is reasonably representative of an average. For example, a rolling average is one such filter. Minimum and maximum delay MUST each be derived in one of the following ways: by taking the lowest and/or highest measured value over a measurement interval or by making use of a filter or other technique to obtain a reasonable representation of a minimum value and a maximum value representative of the interval, with compensation for outliers. Ginsberg, et al. Standards Track [Page 13] RFC 8570 IS-IS TE Metric Extensions March 2019 The measurement interval, any filter coefficients, and any advertisement intervals MUST be configurable per sub-TLV. In addition to the measurement intervals governing re-advertisement, implementations SHOULD provide configurable accelerated advertisement thresholds per sub-TLV, such that: 1. If the measured parameter falls outside a configured upper bound for all but the minimum delay metric (or lower bound for the minimum delay metric only) and the advertised sub-TLV is not already outside that bound, or 2. If the difference between the last advertised value and current measured value exceeds a configured threshold, then 3. The advertisement is made immediately. 4. For sub-TLVs that include an A bit, an additional threshold SHOULD be included corresponding to the threshold for which the performance is considered anomalous (and sub-TLVs with the A bit are sent). The A bit is cleared when the sub-TLV's performance has been below (or re-crosses) this threshold for one or more advertisement intervals to permit failback. To prevent oscillations, only the high threshold or the low threshold (but not both) may be used to trigger any given sub-TLV that supports both. Additionally, once outside the bounds of the threshold, any re-advertisement of a measurement within the bounds would remain governed solely by the measurement interval for that sub-TLV. 6. Announcement Suppression When link-performance values change by small amounts that fall under thresholds that would cause the announcement of a sub-TLV, implementations SHOULD suppress sub-TLV re-advertisement and/or lengthen the period within which the sub-TLVs are refreshed. Only the accelerated advertisement threshold mechanism described in Section 5 may shorten the re-advertisement interval. All suppression and re-advertisement interval backoff timer features SHOULD be configurable. Ginsberg, et al. Standards Track [Page 14] RFC 8570 IS-IS TE Metric Extensions March 2019 7. Network Stability and Announcement Periodicity Sections 5 and 6 provide configurable mechanisms to bound the number of re-advertisements. Instability might occur in very large networks if measurement intervals are set low enough to overwhelm the processing of flooded information at some of the routers in the topology. Therefore, care should be taken in setting these values. Additionally, the default measurement interval for all sub-TLVs SHOULD be 30 seconds. Announcements MUST also be able to be throttled using configurable inter-update throttle timers. The minimum announcement periodicity is one announcement per second. The default value SHOULD be set to 120 seconds. Implementations SHOULD NOT permit the inter-update timer to be lower than the measurement interval. Furthermore, it is RECOMMENDED that any underlying performance- measurement mechanisms not include any significant buffer delay, any significant buffer-induced delay variation, or any significant loss due to buffer overflow or due to active queue management. 8. Enabling and Disabling Sub-TLVs Implementations MUST make it possible to individually enable or disable each sub-TLV based on configuration. 9. Static Metric Override Implementations SHOULD permit static configuration and/or manual override of dynamic measurements for each sub-TLV in order to simplify migration and to mitigate scenarios where dynamic measurements are not possible. 10. Compatibility As per [RFC5305], unrecognized sub-TLVs should be silently ignored. 11. Security Considerations The sub-TLVs introduced in this document allow an operator to advertise state information of links (bandwidth, delay) that could be sensitive and that an operator may not want to disclose. Section 7 describes a mechanism to ensure network stability when the new sub-TLVs defined in this document are advertised. Ginsberg, et al. Standards Track [Page 15] RFC 8570 IS-IS TE Metric Extensions March 2019 Implementations SHOULD follow the described guidelines to mitigate the risk of instability. [RFC5304] describes an authentication method for IS-IS Link State PDUs that allows cryptographic authentication of IS-IS Link State PDUs. It is anticipated that in most deployments, the IS-IS protocol is used within an infrastructure entirely under the control of the same operator. However, it is worth considering that the effect of sending IS-IS Traffic Engineering sub-TLVs over insecure links could include a man-in-the-middle attacker delaying real-time data to a given site or destination; this could negatively affect the value of the data for that site or destination. The use of Link State PDU cryptographic authentication allows mitigation of the risk of man-in-the-middle attacks. 12. IANA Considerations IANA maintains the registry for the sub-TLVs. IANA has registered the following sub-TLVs in the "Sub-TLVs for TLVs 22, 23, 141, 222, and 223" registry: Type Description ---------------------------------------------------- 33 Unidirectional Link Delay 34 Min/Max Unidirectional Link Delay 35 Unidirectional Delay Variation 36 Unidirectional Link Loss 37 Unidirectional Residual Bandwidth 38 Unidirectional Available Bandwidth 39 Unidirectional Utilized Bandwidth Ginsberg, et al. Standards Track [Page 16] RFC 8570 IS-IS TE Metric Extensions March 2019 13. References 13.1. Normative References [IEEE754] Institute of Electrical and Electronics Engineers, "IEEE Standard for Floating-Point Arithmetic", IEEE Std 754-2008. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, <https://www.rfc-editor.org/info/rfc2119>. [RFC4206] Kompella, K. and Y. Rekhter, "Label Switched Paths (LSP) Hierarchy with Generalized Multi-Protocol Label Switching (GMPLS) Traffic Engineering (TE)", RFC 4206, DOI 10.17487/RFC4206, October 2005, <https://www.rfc-editor.org/info/rfc4206>. [RFC5120] Przygienda, T., Shen, N., and N. Sheth, "M-ISIS: Multi Topology (MT) Routing in Intermediate System to Intermediate Systems (IS-ISs)", RFC 5120, DOI 10.17487/RFC5120, February 2008, <https://www.rfc-editor.org/info/rfc5120>. [RFC5304] Li, T. and R. Atkinson, "IS-IS Cryptographic Authentication", RFC 5304, DOI 10.17487/RFC5304, October 2008, <https://www.rfc-editor.org/info/rfc5304>. [RFC5305] Li, T. and H. Smit, "IS-IS Extensions for Traffic Engineering", RFC 5305, DOI 10.17487/RFC5305, October 2008, <https://www.rfc-editor.org/info/rfc5305>. [RFC5316] Chen, M., Zhang, R., and X. Duan, "ISIS Extensions in Support of Inter-Autonomous System (AS) MPLS and GMPLS Traffic Engineering", RFC 5316, DOI 10.17487/RFC5316, December 2008, <https://www.rfc-editor.org/info/rfc5316>. [RFC6119] Harrison, J., Berger, J., and M. Bartlett, "IPv6 Traffic Engineering in IS-IS", RFC 6119, DOI 10.17487/RFC6119, February 2011, <https://www.rfc-editor.org/info/rfc6119>. [RFC7471] Giacalone, S., Ward, D., Drake, J., Atlas, A., and S. Previdi, "OSPF Traffic Engineering (TE) Metric Extensions", RFC 7471, DOI 10.17487/RFC7471, March 2015, <https://www.rfc-editor.org/info/rfc7471>. Ginsberg, et al. Standards Track [Page 17] RFC 8570 IS-IS TE Metric Extensions March 2019 [RFC7810] Previdi, S., Ed., Giacalone, S., Ward, D., Drake, J., and Q. Wu, "IS-IS Traffic Engineering (TE) Metric Extensions", RFC 7810, DOI 10.17487/RFC7810, May 2016, <https://www.rfc-editor.org/info/rfc7810>. [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, <https://www.rfc-editor.org/info/rfc8174>. 13.2. Informative References [RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001, <https://www.rfc-editor.org/info/rfc3209>. [RFC4203] Kompella, K., Ed. and Y. Rekhter, Ed., "OSPF Extensions in Support of Generalized Multi-Protocol Label Switching (GMPLS)", RFC 4203, DOI 10.17487/RFC4203, October 2005, <https://www.rfc-editor.org/info/rfc4203>. [RFC6374] Frost, D. and S. Bryant, "Packet Loss and Delay Measurement for MPLS Networks", RFC 6374, DOI 10.17487/RFC6374, September 2011, <https://www.rfc-editor.org/info/rfc6374>. [RFC6375] Frost, D., Ed. and S. Bryant, Ed., "A Packet Loss and Delay Measurement Profile for MPLS-Based Transport Networks", RFC 6375, DOI 10.17487/RFC6375, September 2011, <https://www.rfc-editor.org/info/rfc6375>. [RFC7285] Alimi, R., Ed., Penno, R., Ed., Yang, Y., Ed., Kiesel, S., Previdi, S., Roome, W., Shalunov, S., and R. Woundy, "Application-Layer Traffic Optimization (ALTO) Protocol", RFC 7285, DOI 10.17487/RFC7285, September 2014, <https://www.rfc-editor.org/info/rfc7285>. [RFC8571] Ginsberg, L., Ed., Previdi, S., Wu, Q., Tantsura, J., and C. Filsfils, "BGP - Link State (BGP-LS) Advertisement of IGP Traffic Engineering Performance Metric Extensions", RFC 8571, DOI 10.17487/RFC8571, March 2019, <https://www.rfc-editor.org/info/rfc8571>. Ginsberg, et al. Standards Track [Page 18] RFC 8570 IS-IS TE Metric Extensions March 2019 Appendix A. Changes from RFC 7810 Errata ID 5293 (https://www.rfc-editor.org/errata/eid5293) correctly identified that in [RFC7810] the length associated with the following sub-TLVs did not match the figures associated with each: 37 Unidirectional Residual Bandwidth 38 Unidirectional Available Bandwidth 39 Unidirectional Utilized Bandwidth The length specified was 4, which did not include the RESERVED field shown in the figures. Subsequent investigation revealed that some implementations had used the specified length (4) and omitted the RESERVED field while other implementations included the specified RESERVED field and used a length of 5. Because these different implementation choices are not interoperable, it was decided that a bis version should be generated to resolve this ambiguity. The choice made here is to omit the unused RESERVED field from these sub-TLVs and use the length of 4. This matches the corresponding advertisements specified in the equivalent OSPF TE specification [RFC7471] and the corresponding BGP - Link State (BGP-LS) specification [RFC8571]. Some minor editorial corrections have also been made. Errata ID 5486 (https://www.rfc-editor.org/errata/eid5486) identified that in Section 4.6 of [RFC7810] the definition of available bandwidth on bundled links used a circular definition, i.e., it used "sum of the component link available bandwidths" when it should have used "sum of the component link residual bandwidths". This has been corrected and clarified. Ginsberg, et al. Standards Track [Page 19] RFC 8570 IS-IS TE Metric Extensions March 2019 Acknowledgements In [RFC7810], the authors recognized Ayman Soliman, Nabil Bitar, David McDysan, Edward Crabbe, Don Fedyk, Hannes Gredler, Uma Chunduri, Alvaro Retana, Brian Weis, and Barry Leiba for their contributions and reviews of this document. The authors also recognized Curtis Villamizar for significant comments and direct content collaboration. For this document, the authors thank Jeff Haas for identifying and reporting the incorrect encoding of the bandwidth-related sub-TLVs. Contributors The following people contributed substantially to the content of this document and should be considered coauthors: Alia Atlas Juniper Networks United States of America Email: akatlas@juniper.net Clarence Filsfils Cisco Systems, Inc. Belgium Email: cfilsfil@cisco.com Ginsberg, et al. Standards Track [Page 20] RFC 8570 IS-IS TE Metric Extensions March 2019 Authors' Addresses Les Ginsberg (editor) Cisco Systems, Inc. Email: ginsberg@cisco.com Stefano Previdi (editor) Huawei Email: stefano@previdi.net Spencer Giacalone Microsoft Email: spencer.giacalone@gmail.com Dave Ward Cisco Systems, Inc. Email: wardd@cisco.com John Drake Juniper Networks 1194 N. Mathilda Ave. Sunnyvale, CA 94089 United States of America Email: jdrake@juniper.net Qin Wu Huawei 101 Software Avenue, Yuhua District Nanjing, Jiangsu 210012 China Email: bill.wu@huawei.com Ginsberg, et al. Standards Track [Page 21]

Display RFC

RFC Number