Packetizer Logo
 
Display RFC

RFC 6665 - SIP-Specific Event Notification

(Formats: TXT)

(Updated By: RFC 7621)

Internet Engineering Task Force (IETF) A.B. Roach Request for Comments: 6665 Tekelec Obsoletes: 3265 July 2012 Updates: 3261, 4660 Category: Standards Track ISSN: 2070-1721
SIP-Specific Event Notification Abstract This document describes an extension to the Session Initiation Protocol (SIP) defined by RFC 3261. The purpose of this extension is to provide an extensible framework by which SIP nodes can request notification from remote nodes indicating that certain events have occurred. Note that the event notification mechanisms defined herein are NOT intended to be a general-purpose infrastructure for all classes of event subscription and notification. This document represents a backwards-compatible improvement on the original mechanism described by RFC 3265, taking into account several years of implementation experience. Accordingly, this document obsoletes RFC 3265. This document also updates RFC 4660 slightly to accommodate some small changes to the mechanism that were discussed in that document. Status of This Memo This is an Internet Standards Track document. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 5741. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at http://www.rfc-editor.org/info/rfc6665. Roach Standards Track [Page 1] RFC 6665 SIP-Specific Event Notification July 2012 Copyright Notice Copyright (c) 2012 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.1. Overview of Operation . . . . . . . . . . . . . . . . . . 5 1.2. Documentation Conventions . . . . . . . . . . . . . . . . 6 2. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. SIP Methods for Event Notification . . . . . . . . . . . . . . 7 3.1. SUBSCRIBE . . . . . . . . . . . . . . . . . . . . . . . . 7 3.1.1. Subscription Duration . . . . . . . . . . . . . . . . 7 3.1.2. Identification of Subscribed Events and Event Classes . . . . . . . . . . . . . . . . . . . . . . . 8 3.1.3. Additional SUBSCRIBE Header Field Values . . . . . . . 9 3.2. NOTIFY . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.2.1. Identification of Reported Events, Event Classes, and Current State . . . . . . . . . . . . . . . . . . 9 4. Node Behavior . . . . . . . . . . . . . . . . . . . . . . . . 10 4.1. Subscriber Behavior . . . . . . . . . . . . . . . . . . . 10 4.1.1. Detecting Support for SIP Events . . . . . . . . . . . 10 4.1.2. Creating and Maintaining Subscriptions . . . . . . . . 10 4.1.3. Receiving and Processing State Information . . . . . . 14 4.1.4. Forking of SUBSCRIBE Requests . . . . . . . . . . . . 16 4.2. Notifier Behavior . . . . . . . . . . . . . . . . . . . . 17 4.2.1. Subscription Establishment and Maintenance . . . . . . 17 4.2.2. Sending State Information to Subscribers . . . . . . . 20 4.2.3. PSTN/Internet Interworking (PINT) Compatibility . . . 23 4.3. Proxy Behavior . . . . . . . . . . . . . . . . . . . . . . 23 4.4. Common Behavior . . . . . . . . . . . . . . . . . . . . . 24 4.4.1. Dialog Creation and Termination . . . . . . . . . . . 24 4.4.2. Notifier Migration . . . . . . . . . . . . . . . . . . 24 4.4.3. Polling Resource State . . . . . . . . . . . . . . . . 25 4.4.4. "Allow-Events" Header Field Usage . . . . . . . . . . 26 4.5. Targeting Subscriptions at Devices . . . . . . . . . . . . 26 4.5.1. Using GRUUs to Route to Devices . . . . . . . . . . . 27 Roach Standards Track [Page 2] RFC 6665 SIP-Specific Event Notification July 2012 4.5.2. Sharing Dialogs . . . . . . . . . . . . . . . . . . . 27 4.6. CANCEL Requests for SUBSCRIBE and NOTIFY Transactions . . 29 5. Event Packages . . . . . . . . . . . . . . . . . . . . . . . . 29 5.1. Appropriateness of Usage . . . . . . . . . . . . . . . . . 29 5.2. Event Template-Packages . . . . . . . . . . . . . . . . . 30 5.3. Amount of State to Be Conveyed . . . . . . . . . . . . . . 31 5.3.1. Complete State Information . . . . . . . . . . . . . . 31 5.3.2. State Deltas . . . . . . . . . . . . . . . . . . . . . 32 5.4. Event Package Responsibilities . . . . . . . . . . . . . . 32 5.4.1. Event Package Name . . . . . . . . . . . . . . . . . . 33 5.4.2. Event Package Parameters . . . . . . . . . . . . . . . 33 5.4.3. SUBSCRIBE Request Bodies . . . . . . . . . . . . . . . 33 5.4.4. Subscription Duration . . . . . . . . . . . . . . . . 33 5.4.5. NOTIFY Request Bodies . . . . . . . . . . . . . . . . 34 5.4.6. Notifier Processing of SUBSCRIBE Requests . . . . . . 34 5.4.7. Notifier generation of NOTIFY requests . . . . . . . . 34 5.4.8. Subscriber Processing of NOTIFY Requests . . . . . . . 34 5.4.9. Handling of Forked Requests . . . . . . . . . . . . . 34 5.4.10. Rate of Notifications . . . . . . . . . . . . . . . . 35 5.4.11. State Aggregation . . . . . . . . . . . . . . . . . . 35 5.4.12. Examples . . . . . . . . . . . . . . . . . . . . . . . 36 5.4.13. Use of URIs to Retrieve State . . . . . . . . . . . . 36 6. Security Considerations . . . . . . . . . . . . . . . . . . . 36 6.1. Access Control . . . . . . . . . . . . . . . . . . . . . . 36 6.2. Notifier Privacy Mechanism . . . . . . . . . . . . . . . . 36 6.3. Denial-of-Service Attacks . . . . . . . . . . . . . . . . 37 6.4. Replay Attacks . . . . . . . . . . . . . . . . . . . . . . 37 6.5. Man-in-the-Middle Attacks . . . . . . . . . . . . . . . . 37 6.6. Confidentiality . . . . . . . . . . . . . . . . . . . . . 38 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 38 7.1. Event Packages . . . . . . . . . . . . . . . . . . . . . . 38 7.1.1. Registration Information . . . . . . . . . . . . . . . 39 7.1.2. Registration Template . . . . . . . . . . . . . . . . 40 7.2. Reason Codes . . . . . . . . . . . . . . . . . . . . . . . 40 7.3. Header Field Names . . . . . . . . . . . . . . . . . . . . 41 7.4. Response Codes . . . . . . . . . . . . . . . . . . . . . . 41 8. Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 8.1. New Methods . . . . . . . . . . . . . . . . . . . . . . . 42 8.1.1. SUBSCRIBE Method . . . . . . . . . . . . . . . . . . . 42 8.1.2. NOTIFY Method . . . . . . . . . . . . . . . . . . . . 42 8.2. New Header Fields . . . . . . . . . . . . . . . . . . . . 42 8.2.1. "Event" Header Field . . . . . . . . . . . . . . . . . 42 8.2.2. "Allow-Events" Header Field . . . . . . . . . . . . . 43 8.2.3. "Subscription-State" Header Field . . . . . . . . . . 43 8.3. New Response Codes . . . . . . . . . . . . . . . . . . . . 43 8.3.1. 202 (Accepted) Response Code . . . . . . . . . . . . . 43 8.3.2. 489 (Bad Event) Response Code . . . . . . . . . . . . 44 8.4. Augmented BNF Definitions . . . . . . . . . . . . . . . . 44 Roach Standards Track [Page 3] RFC 6665 SIP-Specific Event Notification July 2012 9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 45 9.1. Normative References . . . . . . . . . . . . . . . . . . . 45 9.2. Informative References . . . . . . . . . . . . . . . . . . 46 Appendix A. Acknowledgements . . . . . . . . . . . . . . . . . . 48 Appendix B. Changes from RFC 3265 . . . . . . . . . . . . . . . . 48 B.1. Bug 666: Clarify use of "expires=xxx" with "terminated" . 48 B.2. Bug 667: Reason code for unsub/poll not clearly spelled out . . . . . . . . . . . . . . . . . . . . . . . 48 B.3. Bug 669: Clarify: SUBSCRIBE for a duration might be answered with a NOTIFY/expires=0 . . . . . . . . . . . . . 48 B.4. Bug 670: Dialog State Machine needs clarification . . . . 49 B.5. Bug 671: Clarify timeout-based removal of subscriptions . 49 B.6. Bug 672: Mandate "expires" in NOTIFY . . . . . . . . . . . 49 B.7. Bug 673: INVITE 481 response effect clarification . . . . 49 B.8. Bug 677: SUBSCRIBE response matching text in error . . . . 49 B.9. Bug 695: Document is not explicit about response to NOTIFY at subscription termination . . . . . . . . . . . . 49 B.10. Bug 696: Subscription state machine needs clarification . 49 B.11. Bug 697: Unsubscription behavior could be clarified . . . 49 B.12. Bug 699: NOTIFY and SUBSCRIBE are target refresh requests . . . . . . . . . . . . . . . . . . . . . . . . . 50 B.13. Bug 722: Inconsistent 423 reason phrase text . . . . . . . 50 B.14. Bug 741: Guidance needed on when to not include "Allow-Events" . . . . . . . . . . . . . . . . . . . . . . 50 B.15. Bug 744: 5xx to NOTIFY terminates a subscription, but should not . . . . . . . . . . . . . . . . . . . . . . . . 50 B.16. Bug 752: Detection of forked requests is incorrect . . . . 50 B.17. Bug 773: Reason code needs IANA registry . . . . . . . . . 50 B.18. Bug 774: Need new reason for terminating subscriptions to resources that never change . . . . . . . . . . . . . . 50 B.19. Clarify Handling of "Route"/"Record-Route" in NOTIFY . . . 50 B.20. Eliminate Implicit Subscriptions . . . . . . . . . . . . . 51 B.21. Deprecate Dialog Reuse . . . . . . . . . . . . . . . . . . 51 B.22. Rationalize Dialog Creation . . . . . . . . . . . . . . . 51 B.23. Refactor Behavior Sections . . . . . . . . . . . . . . . . 51 B.24. Clarify Sections That Need to Be Present in Event Packages . . . . . . . . . . . . . . . . . . . . . . . . . 51 B.25. Make CANCEL Handling More Explicit . . . . . . . . . . . . 51 B.26. Remove "State Agent" Terminology . . . . . . . . . . . . . 51 B.27. Miscellaneous Changes . . . . . . . . . . . . . . . . . . 52 Roach Standards Track [Page 4] RFC 6665 SIP-Specific Event Notification July 2012 1. Introduction The ability to request asynchronous notification of events proves useful in many types of SIP services for which cooperation between end-nodes is required. Examples of such services include automatic callback services (based on terminal state events), buddy lists (based on user presence events), message waiting indications (based on mailbox state change events), and PSTN and Internet Internetworking (PINT) [RFC2848] status (based on call state events). The methods described in this document provide a framework by which notification of these events can be ordered. The event notification mechanisms defined herein are NOT intended to be a general-purpose infrastructure for all classes of event subscription and notification. Meeting requirements for the general problem set of subscription and notification is far too complex for a single protocol. Our goal is to provide a SIP-specific framework for event notification that is not so complex as to be unusable for simple features, but that is still flexible enough to provide powerful services. Note, however, that event packages based on this framework may define arbitrarily elaborate rules that govern the subscription and notification for the events or classes of events they describe. This document does not describe an extension that may be used directly; it must be extended by other documents (herein referred to as "event packages"). In object-oriented design terminology, it may be thought of as an abstract base class that must be derived into an instantiable class by further extensions. Guidelines for creating these extensions are described in Section 5. 1.1. Overview of Operation The general concept is that entities in the network can subscribe to resource or call state for various resources or calls in the network, and those entities (or entities acting on their behalf) can send notifications when those states change. A typical flow of messages would be: Subscriber Notifier |-----SUBSCRIBE---->| Request state subscription |<-------200--------| Acknowledge subscription |<------NOTIFY----- | Return current state information |--------200------->| |<------NOTIFY----- | Return current state information |--------200------->| Roach Standards Track [Page 5] RFC 6665 SIP-Specific Event Notification July 2012 Subscriptions are expired and must be refreshed by subsequent SUBSCRIBE requests. 1.2. Documentation Conventions There are several paragraphs throughout this document that provide motivational or clarifying text. Such passages are non-normative and are provided only to assist with reader comprehension. These passages are set off from the remainder of the text by being indented thus: This is an example of non-normative explanatory text. It does not form part of the specification and is used only for clarification. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. In particular, implementors need to take careful note of the meaning of "SHOULD" defined in RFC 2119. To rephrase: violation of "SHOULD"- strength requirements requires careful analysis and clearly enumerable reasons. It is a protocol violation to fail to comply with "SHOULD"-strength requirements whimsically or for ease of implementation. 2. Definitions Event Package: An event package is an additional specification that defines a set of state information to be reported by a notifier to a subscriber. Event packages also define further syntax and semantics that are based on the framework defined by this document and are required to convey such state information. Event Template-Package: An event template-package is a special kind of event package that defines a set of states that may be applied to all possible event packages, including itself. Notification: Notification is the act of a notifier sending a NOTIFY request to a subscriber to inform the subscriber of the state of a resource. Notifier: A notifier is a user agent that generates NOTIFY requests for the purpose of notifying subscribers of the state of a resource. Notifiers typically also accept SUBSCRIBE requests to create subscriptions. Roach Standards Track [Page 6] RFC 6665 SIP-Specific Event Notification July 2012 Subscriber: A subscriber is a user agent that receives NOTIFY requests from notifiers; these NOTIFY requests contain information about the state of a resource in which the subscriber is interested. Subscribers typically also generate SUBSCRIBE requests and send them to notifiers to create subscriptions. Subscription: A subscription is a set of application state associated with a dialog. This application state includes a pointer to the associated dialog, the event package name, and possibly an identification token. Event packages will define additional subscription state information. By definition, subscriptions exist in both a subscriber and a notifier. Subscription Migration: Subscription migration is the act of moving a subscription from one notifier to another notifier. 3. SIP Methods for Event Notification 3.1. SUBSCRIBE The SUBSCRIBE method is used to request current state and state updates from a remote node. SUBSCRIBE requests are target refresh requests, as that term is defined in [RFC3261]. 3.1.1. Subscription Duration SUBSCRIBE requests SHOULD contain an "Expires" header field (defined in [RFC3261]). This expires value indicates the duration of the subscription. In order to keep subscriptions effective beyond the duration communicated in the "Expires" header field, subscribers need to refresh subscriptions on a periodic basis using a new SUBSCRIBE request on the same dialog as defined in [RFC3261]. If no "Expires" header field is present in a SUBSCRIBE request, the implied default MUST be defined by the event package being used. 200-class responses to SUBSCRIBE requests also MUST contain an "Expires" header field. The period of time in the response MAY be shorter but MUST NOT be longer than specified in the request. The notifier is explicitly allowed to shorten the duration to zero. The period of time in the response is the one that defines the duration of the subscription. An "expires" parameter on the "Contact" header field has no semantics for the SUBSCRIBE method and is explicitly not equivalent to an "Expires" header field in a SUBSCRIBE request or response. Roach Standards Track [Page 7] RFC 6665 SIP-Specific Event Notification July 2012 A natural consequence of this scheme is that a SUBSCRIBE request with an "Expires" of 0 constitutes a request to unsubscribe from the matching subscription. In addition to being a request to unsubscribe, a SUBSCRIBE request with "Expires" of 0 also causes a fetch of state; see Section 4.4.3. Notifiers may also wish to cancel subscriptions to events; this is useful, for example, when the resource to which a subscription refers is no longer available. Further details on this mechanism are discussed in Section 4.2.2. 3.1.2. Identification of Subscribed Events and Event Classes Identification of events is provided by three pieces of information: Request URI, Event Type, and (optionally) message body. The Request URI of a SUBSCRIBE request, most importantly, contains enough information to route the request to the appropriate entity per the request routing procedures outlined in [RFC3261]. It also contains enough information to identify the resource for which event notification is desired, but not necessarily enough information to uniquely identify the nature of the event (e.g., "sip:adam@example.com" would be an appropriate URI to subscribe to for my presence state; it would also be an appropriate URI to subscribe to the state of my voice mailbox). Subscribers MUST include exactly one "Event" header field in SUBSCRIBE requests, indicating to which event or class of events they are subscribing. The "Event" header field will contain a token that indicates the type of state for which a subscription is being requested. This token will be registered with the IANA and will correspond to an event package that further describes the semantics of the event or event class. If the event package to which the event token corresponds defines behavior associated with the body of its SUBSCRIBE requests, those semantics apply. Event packages may also define parameters for the "Event" header field; if they do so, they must define the semantics for such parameters. Roach Standards Track [Page 8] RFC 6665 SIP-Specific Event Notification July 2012 3.1.3. Additional SUBSCRIBE Header Field Values Because SUBSCRIBE requests create a dialog usage as defined in [RFC3261], they MAY contain an "Accept" header field. This header field, if present, indicates the body formats allowed in subsequent NOTIFY requests. Event packages MUST define the behavior for SUBSCRIBE requests without "Accept" header fields; usually, this will connote a single, default body type. Header values not described in this document are to be interpreted as described in [RFC3261]. 3.2. NOTIFY NOTIFY requests are sent to inform subscribers of changes in state to which the subscriber has a subscription. Subscriptions are created using the SUBSCRIBE method. In legacy implementations, it is possible that other means of subscription creation have been used. However, this specification does not allow the creation of subscriptions except through SUBSCRIBE requests and (for backwards- compatibility) REFER requests [RFC3515]. NOTIFY is a target refresh request, as that term is defined in [RFC3261]. A NOTIFY request does not terminate its corresponding subscription; in other words, a single SUBSCRIBE request may trigger several NOTIFY requests. 3.2.1. Identification of Reported Events, Event Classes, and Current State Identification of events being reported in a notification is very similar to that described for subscription to events (see Section 3.1.2). As in SUBSCRIBE requests, NOTIFY request "Event" header fields MUST contain a single event package name for which a notification is being generated. The package name in the "Event" header field MUST match the "Event" header field in the corresponding SUBSCRIBE request. Event packages may define semantics associated with the body of their NOTIFY requests; if they do so, those semantics apply. NOTIFY request bodies are expected to provide additional details about the nature of the event that has occurred and the resultant resource state. Roach Standards Track [Page 9] RFC 6665 SIP-Specific Event Notification July 2012 When present, the body of the NOTIFY request MUST be formatted into one of the body formats specified in the "Accept" header field of the corresponding SUBSCRIBE request (or the default type according to the event package description, if no "Accept" header field was specified). This body will contain either the state of the subscribed resource or a pointer to such state in the form of a URI (see Section 5.4.13). 4. Node Behavior 4.1. Subscriber Behavior 4.1.1. Detecting Support for SIP Events The extension described in this document does not make use of the "Require" or "Proxy-Require" header fields; similarly, there is no token defined for "Supported" header fields. Potential subscribers may probe for the support of SIP events using the OPTIONS request defined in [RFC3261]. The presence of "SUBSCRIBE" in the "Allow" header field of any request or response indicates support for SIP events; further, in the absence of an "Allow" header field, the simple presence of an "Allow- Events" header field is sufficient to indicate that the node that sent the message is capable of acting as a notifier (see Section 4.4.4). The "methods" parameter for Contact may also be used to specifically announce support for SUBSCRIBE and NOTIFY requests when registering. (See [RFC3840] for details on the "methods" parameter.) 4.1.2. Creating and Maintaining Subscriptions From the subscriber's perspective, a subscription proceeds according to the following state diagram. Events that result in a transition back to the same state are not represented in this diagram. Roach Standards Track [Page 10] RFC 6665 SIP-Specific Event Notification July 2012 +-------------+ | init |<-----------------------+ +-------------+ | | Retry-after Send SUBSCRIBE expires | | V Timer N Fires; | +-------------+ SUBSCRIBE failure | +------------| notify_wait |-- response; --------+ | | +-------------+ or NOTIFY, | | | | state=terminated | | | | | | ++========|===================|============================|==|====++ || | | V | || || Receive NOTIFY, Receive NOTIFY, +-------------+ || || state=active state=pending | terminated | || || | | +-------------+ || || | | Re-subscription A A || || | V times out; | | || || | +-------------+ Receive NOTIFY, | | || || | | pending |-- state=terminated; --+ | || || | +-------------+ or 481 response | || || | | to SUBSCRIBE | || || | Receive NOTIFY, refresh | || || | state=active | || || | | Re-subscription | || || | V times out; | || || | +-------------+ Receive NOTIFY, | || || +----------->| active |-- state=terminated; -----+ || || +-------------+ or 481 response || || to SUBSCRIBE || || Subscription refresh || ++=================================================================++ In the state diagram, "Re-subscription times out" means that an attempt to refresh or update the subscription using a new SUBSCRIBE request does not result in a NOTIFY request before the corresponding Timer N expires. Any transition from "notify_wait" into a "pending" or "active" state results in a new subscription. Note that multiple subscriptions can be generated as the result of a single SUBSCRIBE request (see Section 4.4.1). Each of these new subscriptions exists in its own independent state machine and runs its own set of timers. Roach Standards Track [Page 11] RFC 6665 SIP-Specific Event Notification July 2012 4.1.2.1. Requesting a Subscription SUBSCRIBE is a dialog-creating method, as described in [RFC3261]. When a subscriber wishes to subscribe to a particular state for a resource, it forms a SUBSCRIBE request. If the initial SUBSCRIBE request represents a request outside of a dialog (as it typically will), its construction follows the procedures outlined in [RFC3261] for User Agent Client (UAC) request generation outside of a dialog. This SUBSCRIBE request will be confirmed with a final response. 200-class responses indicate that the subscription has been accepted and that a NOTIFY request will be sent immediately. The "Expires" header field in a 200-class response to SUBSCRIBE request indicates the actual duration for which the subscription will remain active (unless refreshed). The received value might be smaller than the value indicated in the SUBSCRIBE request but cannot be larger; see Section 4.2.1 for details. Non-200-class final responses indicate that no subscription or new dialog usage has been created, and no subsequent NOTIFY request will be sent. All non-200-class responses (with the exception of 489 (Bad Event), described herein) have the same meanings and handling as described in [RFC3261]. For the sake of clarity: if a SUBSCRIBE request contains an "Accept" header field, but that field does not indicate a media type that the notifier is capable of generating in its NOTIFY requests, then the proper error response is 406 (Not Acceptable). 4.1.2.2. Refreshing of Subscriptions At any time before a subscription expires, the subscriber may refresh the timer on such a subscription by sending another SUBSCRIBE request on the same dialog as the existing subscription. The handling for such a request is the same as for the initial creation of a subscription except as described below. If a SUBSCRIBE request to refresh a subscription receives a 404, 405, 410, 416, 480-485, 489, 501, or 604 response, the subscriber MUST consider the subscription terminated. (See [RFC5057] for further details and notes about the effect of error codes on dialogs and usages within dialog, such as subscriptions). If the subscriber wishes to re-subscribe to the state, he does so by composing an unrelated initial SUBSCRIBE request with a freshly generated Call-ID and a new, unique "From" tag (see Section 4.1.2.1). Roach Standards Track [Page 12] RFC 6665 SIP-Specific Event Notification July 2012 If a SUBSCRIBE request to refresh a subscription fails with any error code other than those listed above, the original subscription is still considered valid for the duration of the most recently known "Expires" value as negotiated by the most recent successful SUBSCRIBE transaction, or as communicated by a NOTIFY request in its "Subscription-State" header field "expires" parameter. Note that many such errors indicate that there may be a problem with the network or the notifier such that no further NOTIFY requests will be received. When refreshing a subscription, a subscriber starts Timer N, set to 64*T1, when it sends the SUBSCRIBE request. If this Timer N expires prior to the receipt of a NOTIFY request, the subscriber considers the subscription terminated. If the subscriber receives a success response to the SUBSCRIBE request that indicates that no NOTIFY request will be generated -- such as the 204 response defined for use with the optional extension described in [RFC5839] -- then it MUST cancel Timer N. 4.1.2.3. Unsubscribing Unsubscribing is handled in the same way as refreshing of a subscription, with the "Expires" header field set to "0". Note that a successful unsubscription will also trigger a final NOTIFY request. The final NOTIFY request may or may not contain information about the state of the resource; subscribers need to be prepared to receive final NOTIFY requests both with and without state. 4.1.2.4. Confirmation of Subscription Creation The subscriber can expect to receive a NOTIFY request from each node which has processed a successful subscription or subscription refresh. To ensure that subscribers do not wait indefinitely for a subscription to be established, a subscriber starts a Timer N, set to 64*T1, when it sends a SUBSCRIBE request. If this Timer N expires prior to the receipt of a NOTIFY request, the subscriber considers the subscription failed, and cleans up any state associated with the subscription attempt. Until Timer N expires, several NOTIFY requests may arrive from different destinations (see Section 4.4.1). Each of these requests establishes a new dialog usage and a new subscription. After the expiration of Timer N, the subscriber SHOULD reject any such NOTIFY requests that would otherwise establish a new dialog usage with a 481 (Subscription does not exist) response code. Roach Standards Track [Page 13] RFC 6665 SIP-Specific Event Notification July 2012 Until the first NOTIFY request arrives, the subscriber should consider the state of the subscribed resource to be in a neutral state. Event package specifications MUST define this "neutral state" in such a way that makes sense for their application (see Section 5.4.7). Due to the potential for out-of-order messages, packet loss, and forking, the subscriber MUST be prepared to receive NOTIFY requests before the SUBSCRIBE transaction has completed. Except as noted above, processing of this NOTIFY request is the same as in Section 4.1.3. 4.1.3. Receiving and Processing State Information Subscribers receive information about the state of a resource to which they have subscribed in the form of NOTIFY requests. Upon receiving a NOTIFY request, the subscriber should check that it matches at least one of its outstanding subscriptions; if not, it MUST return a 481 (Subscription does not exist) response unless another 400- or 500-class response is more appropriate. The rules for matching NOTIFY requests with subscriptions that create a new dialog usage are described in Section 4.4.1. Notifications for subscriptions that were created inside an existing dialog match if they are in the same dialog and the "Event" header fields match (as described in Section 8.2.1). If, for some reason, the event package designated in the "Event" header field of the NOTIFY request is not supported, the subscriber will respond with a 489 (Bad Event) response. To prevent spoofing of events, NOTIFY requests SHOULD be authenticated using any defined SIP authentication mechanism, such as those described in Sections 22.2 and 23 of [RFC3261]. NOTIFY requests MUST contain "Subscription-State" header fields that indicate the status of the subscription. If the "Subscription-State" header field value is "active", it means that the subscription has been accepted and (in general) has been authorized. If the header field also contains an "expires" parameter, the subscriber SHOULD take it as the authoritative subscription duration and adjust accordingly. The "retry-after" and "reason" parameters have no semantics for "active". Roach Standards Track [Page 14] RFC 6665 SIP-Specific Event Notification July 2012 If the "Subscription-State" value is "pending", the subscription has been received by the notifier, but there is insufficient policy information to grant or deny the subscription yet. If the header field also contains an "expires" parameter, the subscriber SHOULD take it as the authoritative subscription duration and adjust accordingly. No further action is necessary on the part of the subscriber. The "retry-after" and "reason" parameters have no semantics for "pending". If the "Subscription-State" value is "terminated", the subscriber MUST consider the subscription terminated. The "expires" parameter has no semantics for "terminated" -- notifiers SHOULD NOT include an "expires" parameter on a "Subscription-State" header field with a value of "terminated", and subscribers MUST ignore any such parameter, if present. If a reason code is present, the client should behave as described below. If no reason code or an unknown reason code is present, the client MAY attempt to re-subscribe at any time (unless a "retry-after" parameter is present, in which case the client SHOULD NOT attempt re-subscription until after the number of seconds specified by the "retry-after" parameter). The reason codes defined by this document are: deactivated: The subscription has been terminated, but the subscriber SHOULD retry immediately with a new subscription. One primary use of such a status code is to allow migration of subscriptions between nodes. The "retry-after" parameter has no semantics for "deactivated". probation: The subscription has been terminated, but the client SHOULD retry at some later time (as long as the resource's state is still relevant to the client at that time). If a "retry-after" parameter is also present, the client SHOULD wait at least the number of seconds specified by that parameter before attempting to re-subscribe. rejected: The subscription has been terminated due to change in authorization policy. Clients SHOULD NOT attempt to re-subscribe. The "retry-after" parameter has no semantics for "rejected". timeout: The subscription has been terminated because it was not refreshed before it expired. Clients MAY re-subscribe immediately. The "retry-after" parameter has no semantics for "timeout". This reason code is also associated with polling of resource state, as detailed in Section 4.4.3. giveup: The subscription has been terminated because the notifier could not obtain authorization in a timely fashion. If a "retry- after" parameter is also present, the client SHOULD wait at least Roach Standards Track [Page 15] RFC 6665 SIP-Specific Event Notification July 2012 the number of seconds specified by that parameter before attempting to re-subscribe; otherwise, the client MAY retry immediately, but will likely get put back into pending state. noresource: The subscription has been terminated because the resource state that was being monitored no longer exists. Clients SHOULD NOT attempt to re-subscribe. The "retry-after" parameter has no semantics for "noresource". invariant: The subscription has been terminated because the resource state is guaranteed not to change for the foreseeable future. This may be the case, for example, when subscribing to the location information of a fixed-location land-line telephone. When using this reason code, notifiers are advised to include a "retry-after" parameter with a large value (for example, 31536000 -- or one year) to prevent older clients that are RFC 3265 compliant from periodically re-subscribing. Clients SHOULD NOT attempt to re-subscribe after receiving a reason code of "invariant", regardless of the presence of or value of a "retry- after" parameter. Other specifications may define new reason codes for use with the "Subscription-State" header field. Once the notification is deemed acceptable to the subscriber, the subscriber SHOULD return a 200 response. In general, it is not expected that NOTIFY responses will contain bodies; however, they MAY, if the NOTIFY request contained an "Accept" header field. Other responses defined in [RFC3261] may also be returned, as appropriate. In no case should a NOTIFY transaction extend for any longer than the time necessary for automated processing. In particular, subscribers MUST NOT wait for a user response before returning a final response to a NOTIFY request. 4.1.4. Forking of SUBSCRIBE Requests In accordance with the rules for proxying non-INVITE requests as defined in [RFC3261], successful SUBSCRIBE requests will receive only one 200-class response; however, due to forking, the subscription may have been accepted by multiple nodes. The subscriber MUST therefore be prepared to receive NOTIFY requests with "From:" tags that differ from the "To:" tag received in the SUBSCRIBE 200-class response. Roach Standards Track [Page 16] RFC 6665 SIP-Specific Event Notification July 2012 If multiple NOTIFY requests are received in different dialogs in response to a single SUBSCRIBE request, each dialog represents a different destination to which the SUBSCRIBE request was forked. Subscriber handling in such situations varies by event package; see Section 5.4.9 for details. 4.2. Notifier Behavior 4.2.1. Subscription Establishment and Maintenance Notifiers learn about subscription requests by receiving SUBSCRIBE requests from interested parties. Notifiers MUST NOT create subscriptions except upon receipt of a SUBSCRIBE request. However, for historical reasons, the implicit creation of subscriptions as defined in [RFC3515] is still permitted. [RFC3265] allowed the creation of subscriptions using means other than the SUBSCRIBE method. The only standardized use of this mechanism is the REFER method [RFC3515]. Implementation experience with REFER has shown that the implicit creation of a subscription has a number of undesirable effects, such as the inability to signal the success of a REFER request while signaling a problem with the subscription, and difficulty performing one action without the other. Additionally, the proper exchange of dialog identifiers is difficult without dialog reuse (which has its own set of problems; see Section 4.5). 4.2.1.1. Initial SUBSCRIBE Transaction Processing In no case should a SUBSCRIBE transaction extend for any longer than the time necessary for automated processing. In particular, notifiers MUST NOT wait for a user response before returning a final response to a SUBSCRIBE request. This requirement is imposed primarily to prevent the non-INVITE transaction timeout timer F (see [RFC3261]) from firing during the SUBSCRIBE transaction, since interaction with a user would often exceed 64*T1 seconds. The notifier SHOULD check that the event package specified in the "Event" header field is understood. If not, the notifier SHOULD return a 489 (Bad Event) response to indicate that the specified event/event class is not understood. The notifier SHOULD also perform any necessary authentication and authorization per its local policy. See Section 4.2.1.3. Roach Standards Track [Page 17] RFC 6665 SIP-Specific Event Notification July 2012 The notifier MAY also check that the duration in the "Expires" header field is not too small. If and only if the expiration interval is greater than zero AND smaller than one hour AND less than a notifier- configured minimum, the notifier MAY return a 423 (Interval Too Brief) error that contains a "Min-Expires" header field. The "Min-Expires" header field is described in [RFC3261]. Once the notifier determines that it has enough information to create the subscription (i.e., it understands the event package, the subscription pertains to a known resource, and there are no other barriers to creating the subscription), it creates the subscription and a dialog usage, and returns a 200 (OK) response. When a subscription is created in the notifier, it stores the event package name as part of the subscription information. The "Expires" values present in SUBSCRIBE 200-class responses behave in the same way as they do in REGISTER responses: the server MAY shorten the interval but MUST NOT lengthen it. If the duration specified in a SUBSCRIBE request is unacceptably short, the notifier may be able to send a 423 response, as described earlier in this section. 200-class responses to SUBSCRIBE requests will not generally contain any useful information beyond subscription duration; their primary purpose is to serve as a reliability mechanism. State information will be communicated via a subsequent NOTIFY request from the notifier. The other response codes defined in [RFC3261] may be used in response to SUBSCRIBE requests, as appropriate. 4.2.1.2. Confirmation of Subscription Creation/Refreshing Upon successfully accepting or refreshing a subscription, notifiers MUST send a NOTIFY request immediately to communicate the current resource state to the subscriber. This NOTIFY request is sent on the same dialog as created by the SUBSCRIBE response. If the resource has no meaningful state at the time that the SUBSCRIBE request is processed, this NOTIFY request MAY contain an empty or neutral body. See Section 4.2.2 for further details on NOTIFY request generation. Note that a NOTIFY request is always sent immediately after any 200-class response to a SUBSCRIBE request, regardless of whether the subscription has already been authorized. Roach Standards Track [Page 18] RFC 6665 SIP-Specific Event Notification July 2012 4.2.1.3. Authentication/Authorization of SUBSCRIBE Requests Privacy concerns may require that notifiers apply policy to determine whether a particular subscriber is authorized to subscribe to a certain set of events. Such policy may be defined by mechanisms such as access control lists or real-time interaction with a user. In general, authorization of subscribers prior to authentication is not particularly useful. SIP authentication mechanisms are discussed in [RFC3261]. Note that, even if the notifier node typically acts as a proxy, authentication for SUBSCRIBE requests will always be performed via a 401 (Unauthorized) response, not a 407 (Proxy Authentication Required). Notifiers always act as user agents when accepting subscriptions and sending notifications. Of course, when acting as a proxy, a node will perform normal proxy authentication (using 407). The foregoing explanation is a reminder that notifiers are always user agents and, as such, perform user agent authentication. If authorization fails based on an access list or some other automated mechanism (i.e., it can be automatically authoritatively determined that the subscriber is not authorized to subscribe), the notifier SHOULD reply to the request with a 403 (Forbidden) or 603 (Decline) response, unless doing so might reveal information that should stay private; see Section 6.2. If the notifier owner is interactively queried to determine whether a subscription is allowed, a 200 (OK) response is returned immediately. Note that a NOTIFY request is still formed and sent under these circumstances, as described in the previous section. If subscription authorization was delayed and the notifier wishes to convey that such authorization has been declined, it may do so by sending a NOTIFY request containing a "Subscription-State" header field with a value of "terminated" and a reason parameter of "rejected". 4.2.1.4. Refreshing of Subscriptions When a notifier receives a subscription refresh, assuming that the subscriber is still authorized, the notifier updates the expiration time for subscription. As with the initial subscription, the server MAY shorten the amount of time until expiration but MUST NOT increase it. The final expiration time is placed in the "Expires" header Roach Standards Track [Page 19] RFC 6665 SIP-Specific Event Notification July 2012 field in the response. If the duration specified in a SUBSCRIBE request is unacceptably short, the notifier SHOULD respond with a 423 (Interval Too Brief) response. If no refresh for a notification address is received before its expiration time, the subscription is removed. When removing a subscription, the notifier SHOULD send a NOTIFY request with a "Subscription-State" value of "terminated" to inform it that the subscription is being removed. If such a request is sent, the "Subscription-State" header field SHOULD contain a "reason=timeout" parameter. Clients can cause a subscription to be terminated immediately by sending a SUBSCRIBE request with an "Expires" header field set to '0'. Notifiers largely treat this the same way as any other subscription expiration: they send a NOTIFY request containing a "Subscription-State" of "terminated", with a reason code of "timeout." For consistency with state polling (see Section 4.4.3) and subscription refreshes, the notifier may choose to include resource state in this final NOTIFY request. However, in some cases, including such state makes no sense. Under such circumstances, the notifier may choose to omit state information from the terminal NOTIFY request. The sending of a NOTIFY request when a subscription expires allows the corresponding dialog usage to be terminated, if appropriate. 4.2.2. Sending State Information to Subscribers Notifiers use the NOTIFY method to send information about the state of a resource to subscribers. The notifier's view of a subscription is shown in the following state diagram. Events that result in a transition back to the same state are not represented in this diagram. Roach Standards Track [Page 20] RFC 6665 SIP-Specific Event Notification July 2012 +-------------+ | init | +-------------+ | Receive SUBSCRIBE, Send NOTIFY | V NOTIFY failure, +-------------+ subscription expires, +------------| resp_wait |-- or terminated ----+ | +-------------+ per local policy | | | | | | | | | V Policy grants Policy needed +-------------+ permission | | terminated | | | +-------------+ | | A A | V NOTIFY failure, | | | +-------------+ subscription expires,| | | | pending |-- or terminated -------+ | | +-------------+ per local policy | | | | | Policy changed to | | grant permission | | | | | V NOTIFY failure, | | +-------------+ subscription expires, | +----------->| active |-- or terminated ---------+ +-------------+ per local policy When a SUBSCRIBE request is answered with a 200-class response, the notifier MUST immediately construct and send a NOTIFY request to the subscriber. When a change in the subscribed state occurs, the notifier SHOULD immediately construct and send a NOTIFY request, unless the state transition is caused by a NOTIFY transaction failure. The sending of this NOTIFY message is also subject to authorization, local policy, and throttling considerations. If the NOTIFY request fails due to expiration of SIP Timer F (transaction timeout), the notifier SHOULD remove the subscription. This behavior prevents unnecessary transmission of state information for subscribers who have crashed or disappeared from the network. Because such transmissions will be sent multiple times, per the retransmission algorithm defined in [RFC3261] (instead of the typical single transmission for functioning clients), continuing to service them when no client is available Roach Standards Track [Page 21] RFC 6665 SIP-Specific Event Notification July 2012 to acknowledge them could place undue strain on a network. Upon client restart or reestablishment of a network connection, it is expected that clients will send SUBSCRIBE requests to refresh potentially stale state information; such requests will reinstall subscriptions in all relevant nodes. If the NOTIFY transaction fails due to the receipt of a 404, 405, 410, 416, 480-485, 489, 501, or 604 response to the NOTIFY request, the notifier MUST remove the corresponding subscription. See [RFC5057] for further details and notes about the effect of error codes on dialogs and usages within dialog (such as subscriptions). A notify error response would generally indicate that something has gone wrong with the subscriber or with some proxy on the way to the subscriber. If the subscriber is in error, it makes the most sense to allow the subscriber to rectify the situation (by re-subscribing) once the error condition has been handled. If a proxy is in error, the periodic sending of SUBSCRIBE requests to refresh the expiration timer will reinstall subscription state once the network problem has been resolved. NOTIFY requests MUST contain a "Subscription-State" header field with a value of "active", "pending", or "terminated". The "active" value indicates that the subscription has been accepted and has been authorized (in most cases; see Section 6.2). The "pending" value indicates that the subscription has been received, but that policy information is insufficient to accept or deny the subscription at this time. The "terminated" value indicates that the subscription is not active. If the value of the "Subscription-State" header field is "active" or "pending", the notifier MUST also include in the "Subscription-State" header field an "expires" parameter that indicates the time remaining on the subscription. The notifier MAY use this mechanism to shorten a subscription; however, this mechanism MUST NOT be used to lengthen a subscription. Including expiration information for active and pending subscriptions is necessary in case the SUBSCRIBE request forks, since the response to a forked SUBSCRIBE request may not be received by the subscriber. [RFC3265] allowed the notifier some discretion in the inclusion of this parameter, so subscriber implementations are warned to handle the lack of an "expires" parameter gracefully. Note well that this "expires" value is a parameter on the "Subscription-State" header field NOT the "Expires" header field. Roach Standards Track [Page 22] RFC 6665 SIP-Specific Event Notification July 2012 The period of time for a subscription can be shortened to zero by the notifier. In other words, it is perfectly valid for a SUBSCRIBE request with a non-zero expires to be answered with a NOTIFY request that contains "Subscription-Status: terminated;reason=expired". This merely means that the notifier has shortened the subscription timeout to zero, and the subscription has expired instantaneously. The body may contain valid state, or it may contain a neutral state (see Section 5.4.7). If the value of the "Subscription-State" header field is "terminated", the notifier SHOULD also include a "reason" parameter. The notifier MAY also include a "retry-after" parameter, where appropriate. For details on the value and semantics of the "reason" and "retry-after" parameters, see Section 4.1.3. 4.2.3. PSTN/Internet Interworking (PINT) Compatibility The "Event" header field is considered mandatory for the purposes of this document. However, to maintain compatibility with PINT (see [RFC2848]), notifiers MAY interpret a SUBSCRIBE request with no "Event" header field as requesting a subscription to PINT events. If a notifier does not support PINT, it SHOULD return 489 (Bad Event) to any SUBSCRIBE requests without an "Event" header field. 4.3. Proxy Behavior Proxies need no additional behavior beyond that described in [RFC3261] to support SUBSCRIBE and NOTIFY transactions. If a proxy wishes to see all of the SUBSCRIBE and NOTIFY requests for a given dialog, it MUST add a "Record-Route" header field to the initial SUBSCRIBE request and all NOTIFY requests. It MAY choose to include "Record-Route" in subsequent SUBSCRIBE requests; however, these requests cannot cause the dialog's route set to be modified. Proxies that did not add a "Record-Route" header field to the initial SUBSCRIBE request MUST NOT add a "Record-Route" header field to any of the associated NOTIFY requests. Note that subscribers and notifiers may elect to use Secure/ Multipurpose Internet Mail Extensions (S/MIME) encryption of SUBSCRIBE and NOTIFY requests; consequently, proxies cannot rely on being able to access any information that is not explicitly required to be proxy-readable by [RFC3261]. Roach Standards Track [Page 23] RFC 6665 SIP-Specific Event Notification July 2012 4.4. Common Behavior 4.4.1. Dialog Creation and Termination Dialogs usages are created upon completion of a NOTIFY transaction for a new subscription, unless the NOTIFY request contains a "Subscription-State" of "terminated." Because the dialog usage is established by the NOTIFY request, the route set at the subscriber is taken from the NOTIFY request itself, as opposed to the route set present in the 200-class response to the SUBSCRIBE request. NOTIFY requests are matched to such SUBSCRIBE requests if they contain the same "Call-ID", a "To" header field "tag" parameter that matches the "From" header field "tag" parameter of the SUBSCRIBE request, and the same "Event" header field. Rules for comparisons of the "Event" header fields are described in Section 8.2.1. A subscription is destroyed after a notifier sends a NOTIFY request with a "Subscription-State" of "terminated", or in certain error situations described elsewhere in this document. The subscriber will generally answer such final requests with a 200 (OK) response (unless a condition warranting an alternate response has arisen). Except when the mechanism described in Section 4.5.2 is used, the destruction of a subscription results in the termination of its associated dialog. A subscriber may send a SUBSCRIBE request with an "Expires" header field of 0 in order to trigger the sending of such a NOTIFY request; however, for the purposes of subscription and dialog lifetime, the subscription is not considered terminated until the NOTIFY transaction with a "Subscription-State" of "terminated" completes. 4.4.2. Notifier Migration It is often useful to allow migration of subscriptions between notifiers. Such migration may be effected by sending a NOTIFY request with a "Subscription-State" header field of "terminated" and a reason parameter of "deactivated". This NOTIFY request is otherwise normal and is formed as described in Section 4.2.2. Upon receipt of this NOTIFY request, the subscriber SHOULD attempt to re-subscribe (as described in the preceding sections). Note that this subscription is established on a new dialog, and does not reuse the route set from the previous subscription dialog. Roach Standards Track [Page 24] RFC 6665 SIP-Specific Event Notification July 2012 The actual migration is effected by making a change to the policy (such as routing decisions) of one or more servers to which the SUBSCRIBE request will be sent in such a way that a different node ends up responding to the SUBSCRIBE request. This may be as simple as a change in the local policy in the notifier from which the subscription is migrating so that it serves as a proxy or redirect server instead of a notifier. Whether, when, and why to perform notifier migrations may be described in individual event packages; otherwise, such decisions are a matter of local notifier policy and are left up to individual implementations. 4.4.3. Polling Resource State A natural consequence of the behavior described in the preceding sections is that an immediate fetch without a persistent subscription may be effected by sending a SUBSCRIBE with an "Expires" of 0. Of course, an immediate fetch while a subscription is active may be effected by sending a SUBSCRIBE request with an "Expires" equal to the number of seconds remaining in the subscription. Upon receipt of this SUBSCRIBE request, the notifier (or notifiers, if the SUBSCRIBE request was forked) will send a NOTIFY request containing resource state in the same dialog. Note that the NOTIFY requests triggered by SUBSCRIBE requests with "Expires" header fields of 0 will contain a "Subscription-State" value of "terminated" and a "reason" parameter of "timeout". Polling of event state can cause significant increases in load on the network and notifiers; as such, it should be used only sparingly. In particular, polling SHOULD NOT be used in circumstances in which it will typically result in more network messages than long-running subscriptions. When polling is used, subscribers SHOULD attempt to cache authentication credentials between polls so as to reduce the number of messages sent. Due to the requirement on notifiers to send a NOTIFY request immediately upon receipt of a SUBSCRIBE request, the state provided by polling is limited to the information that the notifier has immediate local access to when it receives the SUBSCRIBE request. If, for example, the notifier generally needs to retrieve state from another network server, then that state will be absent from the NOTIFY request that results from polling. Roach Standards Track [Page 25] RFC 6665 SIP-Specific Event Notification July 2012 4.4.4. "Allow-Events" Header Field Usage The "Allow-Events" header field, if present, MUST include a comprehensive and inclusive list of tokens that indicates the event packages for which the user agent can act as a notifier. In other words, a user agent sending an "Allow-Events" header field is advertising that it can process SUBSCRIBE requests and generate NOTIFY requests for all of the event packages listed in that header field. Any user agent that can act as a notifier for one or more event packages SHOULD include an appropriate "Allow-Events" header field indicating all supported events in all methods which initiate dialogs and their responses (such as INVITE) and OPTIONS responses. This information is very useful, for example, in allowing user agents to render particular interface elements appropriately according to whether the events required to implement the features they represent are supported by the appropriate nodes. On the other hand, it doesn't necessarily make much sense to indicate supported events inside a dialog established by a NOTIFY request if the only event package supported is the one associated with that subscription. Note that "Allow-Events" header fields MUST NOT be inserted by proxies. The "Allow-Events" header field does not include a list of the event template-packages supported by an implementation. If a subscriber wishes to determine which event template-packages are supported by a notifier, it can probe for such support by attempting to subscribe to the event template-packages it wishes to use. For example: to check for support for the templatized package "presence.winfo", a client may attempt to subscribe to that event package for a known resource, using an "Expires" header value of 0. If the response is a 489 error code, then the client can deduce that "presence.winfo" is unsupported. 4.5. Targeting Subscriptions at Devices [RFC3265] defined a mechanism by which subscriptions could share dialogs with invite usages and with other subscriptions. The purpose of this behavior was to allow subscribers to ensure that a subscription arrived at the same device as an established dialog. Unfortunately, the reuse of dialogs has proven to be exceedingly confusing. [RFC5057] attempted to clarify proper behavior in a Roach Standards Track [Page 26] RFC 6665 SIP-Specific Event Notification July 2012 variety of circumstances; however, the ensuing rules remain confusing and prone to implementation error. At the same time, the mechanism described in [RFC5627] now provides a far more elegant and unambiguous means to achieve the same goal. Consequently, the dialog reuse technique described in RFC 3265 is now deprecated. This dialog-sharing technique has also historically been used as a means for targeting an event package at a dialog. This usage can be seen, for example, in certain applications of the REFER method [RFC3515]. With the removal of dialog reuse, an alternate (and more explicit) means of targeting dialogs needs to be used for this type of correlation. The appropriate means of such targeting is left up to the actual event packages. Candidates include the "Target-Dialog" header field [RFC4538], the "Join" header field [RFC3911], and the "Replaces" header field [RFC3891], depending on the semantics desired. Alternately, if the semantics of those header fields do not match the event package's purpose for correlation, event packages can devise their own means of identifying dialogs. For an example of this approach, see the Dialog Event Package [RFC4235]. 4.5.1. Using GRUUs to Route to Devices Notifiers MUST implement the Globally Routable User Agent URI (GRUU) extension defined in [RFC5627], and MUST use a GRUU as their local target. This allows subscribers to explicitly target desired devices. If a subscriber wishes to subscribe to a resource on the same device as an established dialog, it should check whether the remote contact in that dialog is a GRUU (i.e., whether it contains a "gr" URI parameter). If so, the subscriber creates a new dialog, using the GRUU as the Request URI for the new SUBSCRIBE request. Because GRUUs are guaranteed to route to a specific device, this ensures that the subscription will be routed to the same place as the established dialog. 4.5.2. Sharing Dialogs For compatibility with older clients, subscriber and notifier implementations may choose to allow dialog sharing. The behavior of multiple usages within a dialog are described in [RFC5057]. Subscribers MUST NOT attempt to reuse dialogs whose remote target is a GRUU. Roach Standards Track [Page 27] RFC 6665 SIP-Specific Event Notification July 2012 Note that the techniques described in this section are included for backwards-compatibility purposes only. Because subscribers cannot reuse dialogs with a GRUU for their remote target, and because notifiers must use GRUUs as their local target, any two implementations that conform to this specification will automatically use the mechanism described in Section 4.5.1. Further note that the prohibition on reusing dialogs does not exempt implicit subscriptions created by the REFER method. This means that implementations complying with this specification are required to use the "Target-Dialog" mechanism described in [RFC4538] when the remote target is a GRUU. If a subscriber wishes to subscribe to a resource on the same device as an established dialog and the remote contact is not a GRUU, it MAY revert to dialog-sharing behavior. Alternately, it MAY choose to treat the remote party as incapable of servicing the subscription (i.e., the same way it would behave if the remote party did not support SIP events at all). If a notifier receives a SUBSCRIBE request for a new subscription on an existing dialog, it MAY choose to implement dialog sharing behavior. Alternately, it may choose to fail the SUBSCRIBE request with a 403 (Forbidden) response. The error text of such 403 responses SHOULD indicate that dialog sharing is not supported. To implement dialog sharing, subscribers and notifiers perform the following additional processing: o When subscriptions exist in dialogs associated with INVITE-created application state and/or other subscriptions, these sets of application state do not interact beyond the behavior described for a dialog (e.g., route set handling). In particular, multiple subscriptions within a dialog expire independently and require independent subscription refreshes. o If a subscription's destruction leaves no other application state associated with the dialog, the dialog terminates. The destruction of other application state (such as that created by an INVITE) will not terminate the dialog if a subscription is still associated with that dialog. This means that, when dialogs are reused, a dialog created with an INVITE does not necessarily terminate upon receipt of a BYE. Similarly, in the case that several subscriptions are associated with a single dialog, the dialog does not terminate until all the subscriptions in it are destroyed. Roach Standards Track [Page 28] RFC 6665 SIP-Specific Event Notification July 2012 o Subscribers MAY include an "id" parameter in a SUBSCRIBE request's "Event" header field to allow differentiation between multiple subscriptions in the same dialog. This "id" parameter, if present, contains an opaque token that identifies the specific subscription within a dialog. An "id" parameter is only valid within the scope of a single dialog. o If an "id" parameter is present in the SUBSCRIBE request used to establish a subscription, that "id" parameter MUST also be present in all corresponding NOTIFY requests. o When a subscriber refreshes the subscription timer, the SUBSCRIBE request MUST contain the same "Event" header field "id" parameter as was present in the SUBSCRIBE request that created the subscription. (Otherwise, the notifier will interpret the SUBSCRIBE request as a request for a new subscription in the same dialog.) o When a subscription is created in the notifier, it stores any "Event" header field "id" parameter as part of the subscription information (along with the event package name). o If an initial SUBSCRIBE request is sent on a pre-existing dialog, a matching NOTIFY request merely creates a new subscription associated with that dialog. 4.6. CANCEL Requests for SUBSCRIBE and NOTIFY Transactions Neither SUBSCRIBE nor NOTIFY requests can be canceled. If a User Agent Server (UAS) receives a CANCEL request that matches a known SUBSCRIBE or NOTIFY transaction, it MUST respond to the CANCEL request, but otherwise ignore it. In particular, the CANCEL request MUST NOT affect processing of the SUBSCRIBE or NOTIFY request in any way. UACs SHOULD NOT send CANCEL requests for SUBSCRIBE or NOTIFY transactions. 5. Event Packages This section covers several issues that should be taken into consideration when event packages based on the SUBSCRIBE and NOTIFY methods are proposed. 5.1. Appropriateness of Usage When designing an event package using the methods described in this document for event notification, it is important to consider: is SIP Roach Standards Track [Page 29] RFC 6665 SIP-Specific Event Notification July 2012 an appropriate mechanism for the problem set? Is SIP being selected because of some unique feature provided by the protocol (e.g., user mobility) or merely because "it can be done"? If you find yourself defining event packages for notifications related to, for example, network management or the temperature inside your car's engine, you may want to reconsider your selection of protocols. Those interested in extending the mechanism defined in this document are urged to follow the development of "Guidelines for Authors of SIP Extensions" [RFC4485] for further guidance regarding appropriate uses of SIP. Further, it is expected that this mechanism is not to be used in applications where the frequency of reportable events is excessively rapid (e.g., more than about once per second). A SIP network is generally going to be provisioned for a reasonable signaling volume; sending a notification every time a user's GPS position changes by one hundredth of a second could easily overload such a network. 5.2. Event Template-Packages Normal event packages define a set of state applied to a specific type of resource, such as user presence, call state, and messaging mailbox state. Event template-packages are a special type of package that define a set of state applied to other packages, such as statistics, access policy, and subscriber lists. Event template-packages may even be applied to other event template-packages. To extend the object-oriented analogy made earlier, event template- packages can be thought of as templatized C++ packages that must be applied to other packages to be useful. The name of an event template-package as applied to a package is formed by appending a period followed by the event template-package name to the end of the package. For example, if a template-package called "winfo" were being applied to a package called "presence", the event token used in the "Event" header field would be "presence.winfo". This scheme may be arbitrarily extended. For example, application of the "winfo" package to the "presence.winfo" state of a resource would be represented by the name "presence.winfo.winfo". It naturally follows from this syntax that the order in which templates are specified is significant. Roach Standards Track [Page 30] RFC 6665 SIP-Specific Event Notification July 2012 For example: consider a theoretical event template-package called "list". The event "presence.winfo.list" would be the application of the "list" template to "presence.winfo", which would presumably be a list of winfo state associated with presence. On the other hand, the event "presence.list.winfo" would represent the application of winfo to "presence.list", which would be represent the winfo state of a list of presence information. Event template-packages must be defined so that they can be applied to any arbitrary package. In other words, event template-packages cannot be specifically tied to one or a few "parent" packages in such a way that they will not work with other packages. 5.3. Amount of State to Be Conveyed When designing event packages, it is important to consider the type of information that will be conveyed during a notification. A natural temptation is to convey merely the event (e.g., "a new voice message just arrived") without accompanying state (e.g., "7 total voice messages"). This complicates implementation of subscribing entities (since they have to maintain complete state for the entity to which they have subscribed), and also is particularly susceptible to synchronization problems. This problem has two possible solutions that event packages may choose to implement. 5.3.1. Complete State Information In general, event packages need to be able to convey a well-defined and complete state, rather than just a stream of events. If it is not possible to describe complete system state for transmission in NOTIFY requests, then the problem set is not a good candidate for an event package. For packages that typically convey state information that is reasonably small (on the order of 1 KB or so), it is suggested that event packages are designed so as to send complete state information whenever an event occurs. In some circumstances, conveying the current state alone may be insufficient for a particular class of events. In these cases, the event packages should include complete state information along with the event that occurred. For example, conveying "no customer service representatives available" may not be as useful as conveying "no customer service representatives available; representative sip:46@cs.xyz.int just logged off". Roach Standards Track [Page 31] RFC 6665 SIP-Specific Event Notification July 2012 5.3.2. State Deltas In the case that the state information to be conveyed is large, the event package may choose to detail a scheme by which NOTIFY requests contain state deltas instead of complete state. Such a scheme would work as follows: any NOTIFY request sent in immediate response to a SUBSCRIBE request contains full state information. NOTIFY requests sent because of a state change will contain only the state information that has changed; the subscriber will then merge this information into its current knowledge about the state of the resource. Any event package that supports delta changes to states MUST include a version number that increases by exactly one for each NOTIFY transaction in a subscription. Note that the state version number appears in the body of the message, not in a SIP header field. If a NOTIFY request arrives that has a version number that is incremented by more than one, the subscriber knows that a state delta has been missed; it ignores the NOTIFY request containing the state delta (except for the version number, which it retains to detect message loss), and re-sends a SUBSCRIBE request to force a NOTIFY request containing a complete state snapshot. 5.4. Event Package Responsibilities Event packages are not required to reiterate any of the behavior described in this document, although they may choose to do so for clarity or emphasis. In general, though, such packages are expected to describe only the behavior that extends or modifies the behavior described in this document. Note that any behavior designated with "SHOULD" or "MUST" in this document is not allowed to be weakened by extension documents; however, such documents may elect to strengthen "SHOULD" requirements to "MUST" requirements if required by their application. In addition to the normal sections expected in Standards Track RFCs and SIP extension documents, authors of event packages need to address each of the issues detailed in the following subsections. For clarity: well-formed event package definitions contain sections addressing each of these issues, ideally in the same order and with the same titles as these subsections. Roach Standards Track [Page 32] RFC 6665 SIP-Specific Event Notification July 2012 5.4.1. Event Package Name This section, which MUST be present, defines the token name to be used to designate the event package. It MUST include the information that appears in the IANA registration of the token. For information on registering such types, see Section 7. 5.4.2. Event Package Parameters If parameters are to be used on the "Event" header field to modify the behavior of the event package, the syntax and semantics of such header fields MUST be clearly defined. Any "Event" header field parameters defined by an event package MUST be registered in the "Header Field Parameters and Parameter Values" registry defined by [RFC3968]. An "Event" header field parameter, once registered in conjunction with an event package, MUST NOT be reused with any other event package. Non-event-package specifications MAY define "Event" header field parameters that apply across all event packages (with emphasis on "all", as opposed to "several"), such as the "id" parameter defined in this document. The restriction of a parameter to use with a single event package only applies to parameters that are defined in conjunction with an event package. 5.4.3. SUBSCRIBE Request Bodies It is expected that most, but not all, event packages will define syntax and semantics for SUBSCRIBE request bodies; these bodies will typically modify, expand, filter, throttle, and/or set thresholds for the class of events being requested. Designers of event packages are strongly encouraged to reuse existing media types for message bodies where practical. See [RFC4288] for information on media type specification and registration. This mandatory section of an event package defines what type or types of event bodies are expected in SUBSCRIBE requests (or specify that no event bodies are expected). It should point to detailed definitions of syntax and semantics for all referenced body types. 5.4.4. Subscription Duration It is RECOMMENDED that event packages give a suggested range of times considered reasonable for the duration of a subscription. Such packages MUST also define a default "Expires" value to be used if none is specified. Roach Standards Track [Page 33] RFC 6665 SIP-Specific Event Notification July 2012 5.4.5. NOTIFY Request Bodies The NOTIFY request body is used to report state on the resource being monitored. Each package MUST define what type or types of event bodies are expected in NOTIFY requests. Such packages MUST specify or cite detailed specifications for the syntax and semantics associated with such event bodies. Event packages also MUST define which media type is to be assumed if none are specified in the "Accept" header field of the SUBSCRIBE request. 5.4.6. Notifier Processing of SUBSCRIBE Requests This section describes the processing to be performed by the notifier upon receipt of a SUBSCRIBE request. Such a section is required. Information in this section includes details of how to authenticate subscribers and authorization issues for the package. 5.4.7. Notifier generation of NOTIFY requests This section of an event package describes the process by which the notifier generates and sends a NOTIFY request. This includes detailed information about what events cause a NOTIFY request to be sent, how to compute the state information in the NOTIFY, how to generate neutral or fake state information to hide authorization delays and decisions from users, and whether state information is complete or what the deltas are for notifications; see Section 5.3. Such a section is required. This section may optionally describe the behavior used to process the subsequent response. 5.4.8. Subscriber Processing of NOTIFY Requests This section of an event package describes the process followed by the subscriber upon receipt of a NOTIFY request, including any logic required to form a coherent resource state (if applicable). 5.4.9. Handling of Forked Requests Each event package MUST specify whether forked SUBSCRIBE requests are allowed to install multiple subscriptions. If such behavior is not allowed, the first potential dialog- establishing message will create a dialog. All subsequent NOTIFY requests that correspond to the SUBSCRIBE request (i.e., have Roach Standards Track [Page 34] RFC 6665 SIP-Specific Event Notification July 2012 matching "To", "From", "Call-ID", and "Event" header fields, as well as "From" header field "tag" parameter and "Event" header field "id" parameter) but that do not match the dialog would be rejected with a 481 response. Note that the 200-class response to the SUBSCRIBE request can arrive after a matching NOTIFY request has been received; such responses might not correlate to the same dialog established by the NOTIFY request. Except as required to complete the SUBSCRIBE transaction, such non-matching 200-class responses are ignored. If installing of multiple subscriptions by way of a single forked SUBSCRIBE request is allowed, the subscriber establishes a new dialog towards each notifier by returning a 200-class response to each NOTIFY request. Each dialog is then handled as its own entity and is refreshed independently of the other dialogs. In the case that multiple subscriptions are allowed, the event package MUST specify whether merging of the notifications to form a single state is required, and how such merging is to be performed. Note that it is possible that some event packages may be defined in such a way that each dialog is tied to a mutually exclusive state that is unaffected by the other dialogs; this MUST be clearly stated if it is the case. 5.4.10. Rate of Notifications Each event package is expected to define a requirement ("SHOULD" or "MUST" strength) that defines an absolute maximum on the rate at which notifications are allowed to be generated by a single notifier. Each package MAY further define a throttle mechanism that allows subscribers to further limit the rate of notification. 5.4.11. State Aggregation Many event packages inherently work by collecting information about a resource from a number of other sources -- either through the use of PUBLISH [RFC3903], by subscribing to state information, or through other state-gathering mechanisms. Event packages that involve retrieval of state information for a single resource from more than one source need to consider how notifiers aggregate information into a single, coherent state. Such packages MUST specify how notifiers aggregate information and how they provide authentication and authorization. Roach Standards Track [Page 35] RFC 6665 SIP-Specific Event Notification July 2012 5.4.12. Examples Event packages SHOULD include several demonstrative message flow diagrams paired with several typical, syntactically correct, and complete messages. It is RECOMMENDED that documents describing event packages clearly indicate that such examples are informative and not normative, with instructions that implementors refer to the main text of the document for exact protocol details. 5.4.13. Use of URIs to Retrieve State Some types of event packages may define state information that is potentially too large to reasonably send in a SIP message. To alleviate this problem, event packages may include the ability to convey a URI instead of state information; this URI will then be used to retrieve the actual state information. [RFC4483] defines a mechanism that can be used by event packages to convey information in such a fashion. 6. Security Considerations 6.1. Access Control The ability to accept subscriptions should be under the direct control of the notifier's user, since many types of events may be considered private. Similarly, the notifier should have the ability to selectively reject subscriptions based on the subscriber identity (based on access control lists), using standard SIP authentication mechanisms. The methods for creation and distribution of such access control lists are outside the scope of this document. 6.2. Notifier Privacy Mechanism The mere act of returning certain 400- and 600-class responses to SUBSCRIBE requests may, under certain circumstances, create privacy concerns by revealing sensitive policy information. In these cases, the notifier SHOULD always return a 200 (OK) response. While the subsequent NOTIFY request may not convey true state, it MUST appear to contain a potentially correct piece of data from the point of view of the subscriber, indistinguishable from a valid response. Information about whether a user is authorized to subscribe to the requested state is never conveyed back to the original user under these circumstances. Roach Standards Track [Page 36] RFC 6665 SIP-Specific Event Notification July 2012 Individual packages and their related documents for which such a mode of operation makes sense can further describe how and why to generate such potentially correct data. For example, such a mode of operation is mandated by [RFC2779] for user presence information. 6.3. Denial-of-Service Attacks The current model (one SUBSCRIBE request triggers a SUBSCRIBE response and one or more NOTIFY requests) is a classic setup for an amplifier node to be used in a smurf attack [CERT1998a]. Also, the creation of state upon receipt of a SUBSCRIBE request can be used by attackers to consume resources on a victim's machine, rendering it unusable. To reduce the chances of such an attack, implementations of notifiers SHOULD require authentication. Authentication issues are discussed in [RFC3261]. 6.4. Replay Attacks Replaying of either SUBSCRIBE or NOTIFY requests can have detrimental effects. In the case of SUBSCRIBE requests, an attacker may be able to install any arbitrary subscription that it witnessed being installed at some point in the past. Replaying of NOTIFY requests may be used to spoof old state information (although a good versioning mechanism in the body of the NOTIFY requests may help mitigate such an attack). Note that the prohibition on sending NOTIFY requests to nodes that have not subscribed to an event also aids in mitigating the effects of such an attack. To prevent such attacks, implementations SHOULD require authentication with anti-replay protection. Authentication issues are discussed in [RFC3261]. 6.5. Man-in-the-Middle Attacks Even with authentication, man-in-the-middle attacks using SUBSCRIBE requests may be used to install arbitrary subscriptions, hijack existing subscriptions, terminate outstanding subscriptions, or modify the resource to which a subscription is being made. To prevent such attacks, implementations SHOULD provide integrity protection across "Contact", "Route", "Expires", "Event", and "To" header fields (at a minimum) of SUBSCRIBE requests. If SUBSCRIBE Roach Standards Track [Page 37] RFC 6665 SIP-Specific Event Notification July 2012 request bodies are used to define further information about the state of the call, they SHOULD be included in the integrity protection scheme. Man-in-the-middle attacks may also attempt to use NOTIFY requests to spoof arbitrary state information and/or terminate outstanding subscriptions. To prevent such attacks, implementations SHOULD provide integrity protection across the "Call-ID", "CSeq", and "Subscription-State" header fields and the bodies of NOTIFY requests. Integrity protection of message header fields and bodies is discussed in [RFC3261]. 6.6. Confidentiality The state information contained in a NOTIFY request has the potential to contain sensitive information. Implementations MAY encrypt such information to ensure confidentiality. While less likely, it is also possible that the information contained in a SUBSCRIBE request contains information that users might not want to have revealed. Implementations MAY encrypt such information to ensure confidentiality. To allow the remote party to hide information it considers sensitive, all implementations SHOULD be able to handle encrypted SUBSCRIBE and NOTIFY requests. The mechanisms for providing confidentiality are detailed in [RFC3261]. 7. IANA Considerations With the exception of Section 7.2, the subsections here are for current reference, carried over from the original specification (RFC 3265). IANA has updated all registry references that pointed to RFC 3265 to instead indicate this document and created the new "reason code" registry described in Section 7.2. 7.1. Event Packages This document defines an event-type namespace that requires a central coordinating body. The body chosen for this coordination is the Internet Assigned Numbers Authority (IANA). Roach Standards Track [Page 38] RFC 6665 SIP-Specific Event Notification July 2012 There are two different types of event-types: normal event packages and event template-packages; see Section 5.2. To avoid confusion, template-package names and package names share the same namespace; in other words, an event template-package is forbidden from sharing a name with a package. Policies for registration of SIP event packages and SIP event package templates are defined in Section 4.1 of [RFC5727]. Registrations with the IANA are required to include the token being registered and whether the token is a package or a template-package. Further, packages must include contact information for the party responsible for the registration and/or a published document that describes the event package. Event template-package token registrations are also required to include a pointer to the published RFC that defines the event template-package. Registered tokens to designate packages and template-packages are disallowed from containing the character ".", which is used to separate template-packages from packages. 7.1.1. Registration Information This document specifies no package or template-package names. All entries in this table are added by other documents. The remainder of the text in this section gives an example of the type of information to be maintained by the IANA; it also demonstrates all four possible permutations of package type, contact, and reference. The table below lists the event packages and template-packages defined for use with the "SIP-Specific Event Notification" mechanism [RFC 6665]. Each name is designated as a package or a template- package under "Type". Package Name Type Contact Reference ------------ ---- ------- --------- example1 package [Doe] [RFCnnnn] example2 package [RFCnnnn] example3 template [Doe] [RFCnnnn] example4 template [RFCnnnn] PEOPLE ------ [Doe] John Doe <john.doe@example.com> REFERENCES ---------- [RFCnnnn] Doe, J., "Sample Document", RFC nnnn, Month YYYY. Roach Standards Track [Page 39] RFC 6665 SIP-Specific Event Notification July 2012 7.1.2. Registration Template To: ietf-sip-events@iana.org Subject: Registration of new SIP event package Package name: (Package names must conform to the syntax described in Section 8.2.1.) Is this registration for a Template-Package: (indicate yes or no) Published specification(s): (Template-packages require a published RFC. Other packages may reference a specification when appropriate.) Person & email address to contact for further information: (self-explanatory) 7.2. Reason Codes This document further defines "reason" codes for use in the "Subscription-State" header field (see Section 4.1.3). Following the policies outlined in "Guidelines for Writing an IANA Considerations Section in RFCs" [RFC5226], new reason codes require a Standards Action. Registrations with the IANA include the reason code being registered and a reference to a published document that describes the event package. Insertion of such values takes place as part of the RFC publication process or as the result of liaison activity between standards development organizations (SDOs), the result of which will be publication of an associated RFC. New reason codes must conform to the syntax of the ABNF "token" element defined in [RFC3261]. [RFC4660] defined a new reason code prior to the establishment of an IANA registry. We include its reason code ("badfilter") in the initial list of reason codes to ensure a complete registry. The IANA registry for reason codes has been initialized with the following values: Roach Standards Track [Page 40] RFC 6665 SIP-Specific Event Notification July 2012 Reason Code Reference ----------- --------- deactivated [RFC6665] probation [RFC6665] rejected [RFC6665] timeout [RFC6665] giveup [RFC6665] noresource [RFC6665] invariant [RFC6665] badfilter [RFC4660] REFERENCES ---------- [RFC6665] A.B. Roach, "SIP-Specific Event Notification", RFC 6665, July 2012. [RFC4660] Khartabil, H., Leppanen, E., Lonnfors, M., and J. Costa-Requena, "Functional Description of Event Notification Filtering", September 2006. 7.3. Header Field Names This document registers three new header field names, described elsewhere in this document. These header fields are defined by the following information, which is to be added to the header field sub- registry under http://www.iana.org/assignments/sip-parameters. Header Name: Allow-Events Compact Form: u Header Name: Subscription-State Compact Form: (none) Header Name: Event Compact Form: o 7.4. Response Codes This document registers two new response codes. These response codes are defined by the following information, which is to be added to the method and response-code sub-registry under http://www.iana.org/assignments/sip-parameters. Response Code Number: 202 Default Reason Phrase: Accepted Response Code Number: 489 Default Reason Phrase: Bad Event Roach Standards Track [Page 41] RFC 6665 SIP-Specific Event Notification July 2012 8. Syntax This section describes the syntax extensions required for event notification in SIP. Semantics are described in Section 4. Note that the formal syntax definitions described in this document are expressed in the ABNF format used in [RFC3261] and contain references to elements defined therein. 8.1. New Methods This document describes two new SIP methods: SUBSCRIBE and NOTIFY. 8.1.1. SUBSCRIBE Method "SUBSCRIBE" is added to the definition of the element "Method" in the SIP message grammar. Like all SIP method names, the SUBSCRIBE method name is case sensitive. The SUBSCRIBE method is used to request asynchronous notification of an event or set of events at a later time. 8.1.2. NOTIFY Method "NOTIFY" is added to the definition of the element "Method" in the SIP message grammar. The NOTIFY method is used to notify a SIP node that an event that has been requested by an earlier SUBSCRIBE method has occurred. It may also provide further details about the event. 8.2. New Header Fields 8.2.1. "Event" Header Field Event is added to the definition of the element "message-header field" in the SIP message grammar. For the purposes of matching NOTIFY requests with SUBSCRIBE requests, the event-type portion of the "Event" header field is compared byte by byte, and the "id" parameter token (if present) is compared byte by byte. An "Event" header field containing an "id" parameter never matches an "Event" header field without an "id" parameter. No other parameters are considered when performing a comparison. SUBSCRIBE responses are matched per the transaction handling rules in [RFC3261]. Roach Standards Track [Page 42] RFC 6665 SIP-Specific Event Notification July 2012 Note that the foregoing text means that "Event: foo; id=1234" would match "Event: foo; param=abcd; id=1234", but not "Event: foo" ("id" does not match) or "Event: Foo; id=1234" ("Event" portion does not match). This document does not define values for event-types. These values will be defined by individual event packages and MUST be registered with the IANA. There MUST be exactly one event type listed per "Event" header field. Multiple events per message are disallowed. The "Event" header field is defined only for use in SUBSCRIBE and NOTIFY requests and other requests whose definition explicitly calls for its use. It MUST NOT appear in any other SIP requests and MUST NOT appear in responses. 8.2.2. "Allow-Events" Header Field "Allow-Events" is added to the definition of the element "general- header field" in the SIP message grammar. Its usage is described in Section 4.4.4. User agents MAY include the "Allow-Events" header field in any request or response, as long as its contents comply with the behavior described in Section 4.4.4. 8.2.3. "Subscription-State" Header Field "Subscription-State" is added to the definition of the element "request-header" field in the SIP message grammar. Its usage is described in Section 4.1.3. "Subscription-State" header fields are defined for use in NOTIFY requests only. They MUST NOT appear in other SIP requests or responses. 8.3. New Response Codes 8.3.1. 202 (Accepted) Response Code For historical purposes, the 202 (Accepted) response code is added to the "Success" header field definition. This document does not specify the use of the 202 response code in conjunction with the SUBSCRIBE or NOTIFY methods. Previous versions of the SIP Events Framework assigned specific meaning to the 202 response code. Roach Standards Track [Page 43] RFC 6665 SIP-Specific Event Notification July 2012 Due to response handling in forking cases, any 202 response to a SUBSCRIBE request may be absorbed by a proxy, and thus it can never be guaranteed to be received by the UAC. Furthermore, there is no actual processing difference for a 202 as compared to a 200; a NOTIFY request is sent after the subscription is processed, and it conveys the correct state. SIP interoperability tests found that implementations were handling 202 differently from 200, leading to incompatibilities. Therefore, the 202 response is being deprecated to make it clear there is no such difference and 202 should not be handled differently than 200. Implementations conformant with the current specification MUST treat an incoming 202 response as identical to a 200 response and MUST NOT generate 202 response codes to SUBSCRIBE or NOTIFY requests. This document also updates [RFC4660], which reiterates the 202-based behavior in several places. Implementations compliant with the present document MUST NOT send a 202 response to a SUBSCRIBE request and will send an alternate success response (such as 200) in its stead. 8.3.2. 489 (Bad Event) Response Code The 489 event response is added to the "Client-Error" header field definition. 489 (Bad Event) is used to indicate that the server did not understand the event package specified in a "Event" header field. 8.4. Augmented BNF Definitions The Augmented BNF [RFC5234] definitions for the various new and modified syntax elements follows. The notation is as used in [RFC3261], and any elements not defined in this section are as defined in SIP and the documents to which it refers. SUBSCRIBEm = %x53.55.42.53.43.52.49.42.45 ; SUBSCRIBE in caps NOTIFYm = %x4E.4F.54.49.46.59 ; NOTIFY in caps extension-method = SUBSCRIBEm / NOTIFYm / token Event = ( "Event" / "o" ) HCOLON event-type *( SEMI event-param ) event-type = event-package *( "." event-template ) event-package = token-nodot event-template = token-nodot token-nodot = 1*( alphanum / "-" / "!" / "%" / "*" / "_" / "+" / "`" / "'" / "~" ) ; The use of the "id" parameter is deprecated; it is included ; for backwards-compatibility purposes only. Roach Standards Track [Page 44] RFC 6665 SIP-Specific Event Notification July 2012 event-param = generic-param / ( "id" EQUAL token ) Allow-Events = ( "Allow-Events" / "u" ) HCOLON event-type *(COMMA event-type) Subscription-State = "Subscription-State" HCOLON substate-value *( SEMI subexp-params ) substate-value = "active" / "pending" / "terminated" / extension-substate extension-substate = token subexp-params = ("reason" EQUAL event-reason-value) / ("expires" EQUAL delta-seconds) / ("retry-after" EQUAL delta-seconds) / generic-param event-reason-value = "deactivated" / "probation" / "rejected" / "timeout" / "giveup" / "noresource" / "invariant" / event-reason-extension event-reason-extension = token 9. References 9.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2848] Petrack, S. and L. Conroy, "The PINT Service Protocol: Extensions to SIP and SDP for IP Access to Telephone Call Services", RFC 2848, June 2000. [RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP: Session Initiation Protocol", RFC 3261, June 2002. [RFC3265] Roach, A., "Session Initiation Protocol (SIP)-Specific Event Notification", RFC 3265, June 2002. [RFC3968] Camarillo, G., "The Internet Assigned Number Authority (IANA) Header Field Parameter Registry for the Session Initiation Protocol (SIP)", BCP 98, RFC 3968, December 2004. Roach Standards Track [Page 45] RFC 6665 SIP-Specific Event Notification July 2012 [RFC4483] Burger, E., "A Mechanism for Content Indirection in Session Initiation Protocol (SIP) Messages", RFC 4483, May 2006. [RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 5226, May 2008. [RFC5234] Crocker, D. and P. Overell, "Augmented BNF for Syntax Specifications: ABNF", STD 68, RFC 5234, January 2008. [RFC5627] Rosenberg, J., "Obtaining and Using Globally Routable User Agent URIs (GRUUs) in the Session Initiation Protocol (SIP)", RFC 5627, October 2009. [RFC5727] Peterson, J., Jennings, C., and R. Sparks, "Change Process for the Session Initiation Protocol (SIP) and the Real-time Applications and Infrastructure Area", BCP 67, RFC 5727, March 2010. 9.2. Informative References [RFC2779] Day, M., Aggarwal, S., Mohr, G., and J. Vincent, "Instant Messaging / Presence Protocol Requirements", RFC 2779, February 2000. [RFC3515] Sparks, R., "The Session Initiation Protocol (SIP) Refer Method", RFC 3515, April 2003. [RFC3840] Rosenberg, J., Schulzrinne, H., and P. Kyzivat, "Indicating User Agent Capabilities in the Session Initiation Protocol (SIP)", RFC 3840, August 2004. [RFC3891] Mahy, R., Biggs, B., and R. Dean, "The Session Initiation Protocol (SIP) "Replaces" Header", RFC 3891, September 2004. [RFC3903] Niemi, A., "Session Initiation Protocol (SIP) Extension for Event State Publication", RFC 3903, October 2004. [RFC3911] Mahy, R. and D. Petrie, "The Session Initiation Protocol (SIP) "Join" Header", RFC 3911, October 2004. [RFC4235] Rosenberg, J., Schulzrinne, H., and R. Mahy, "An INVITE- Initiated Dialog Event Package for the Session Initiation Protocol (SIP)", RFC 4235, November 2005. Roach Standards Track [Page 46] RFC 6665 SIP-Specific Event Notification July 2012 [RFC4288] Freed, N. and J. Klensin, "Media Type Specifications and Registration Procedures", BCP 13, RFC 4288, December 2005. [RFC4485] Rosenberg, J. and H. Schulzrinne, "Guidelines for Authors of Extensions to the Session Initiation Protocol (SIP)", RFC 4485, May 2006. [RFC4538] Rosenberg, J., "Request Authorization through Dialog Identification in the Session Initiation Protocol (SIP)", RFC 4538, June 2006. [RFC4660] Khartabil, H., Leppanen, E., Lonnfors, M., and J. Costa- Requena, "Functional Description of Event Notification Filtering", RFC 4660, September 2006. [RFC5057] Sparks, R., "Multiple Dialog Usages in the Session Initiation Protocol", RFC 5057, November 2007. [RFC5839] Niemi, A. and D. Willis, "An Extension to Session Initiation Protocol (SIP) Events for Conditional Event Notification", RFC 5839, May 2010. [CERT1998a] CERT, "CERT Advisory CA-1998-01: Smurf IP Denial-of- Service Attacks", 1998, <http://www.cert.org/advisories/CA-1998-01.html>. Roach Standards Track [Page 47] RFC 6665 SIP-Specific Event Notification July 2012 Appendix A. Acknowledgements Thanks to the participants in the Events BOF at the 48th IETF meeting in Pittsburgh, as well as those who gave ideas and suggestions on the SIP Events mailing list. In particular, I wish to thank Henning Schulzrinne of Columbia University for coming up with the final three-tiered event identification scheme, Sean Olson for miscellaneous guidance, Jonathan Rosenberg for a thorough scrubbing of the first draft version, and the authors of the "SIP Extensions for Presence" document for their input to SUBSCRIBE and NOTIFY request semantics. I also owe a debt of gratitude to all the implementors who have provided feedback on areas of confusion or difficulty in the original specification. In particular, Robert Sparks' Herculean efforts organizing, running, and collecting data from the SIPit events have proven invaluable in shaking out specification bugs. Robert Sparks is also responsible for untangling the dialog usage mess, in the form of RFC 5057 [RFC5057]. Appendix B. Changes from RFC 3265 This document represents several changes from the mechanism originally described in RFC 3265. This section summarizes those changes. Bug numbers refer to the identifiers for the bug reports kept on file at http://bugs.sipit.net/. B.1. Bug 666: Clarify use of "expires=xxx" with "terminated" Strengthened language in Section 4.1.3 to clarify that "expires" should not be sent with "terminated", and must be ignored if received. B.2. Bug 667: Reason code for unsub/poll not clearly spelled out Clarified description of "timeout" in Section 4.1.3. (n.b., the text in Section 4.4.3 is actually pretty clear about this). B.3. Bug 669: Clarify: SUBSCRIBE for a duration might be answered with a NOTIFY/expires=0 Added clarifying text to Section 4.2.2 explaining that shortening a subscription to zero seconds is valid. Also added sentence to Section 3.1.1 explicitly allowing shortening to zero. Roach Standards Track [Page 48] RFC 6665 SIP-Specific Event Notification July 2012 B.4. Bug 670: Dialog State Machine needs clarification The issues associated with the bug deal exclusively with the handling of multiple usages with a dialog. This behavior has been deprecated and moved to Section 4.5.2. This section, in turn, cites [RFC5057], which addresses all of the issues in Bug 670. B.5. Bug 671: Clarify timeout-based removal of subscriptions Changed Section 4.2.2 to specifically cite Timer F (so as to avoid ambiguity between transaction timeouts and retransmission timeouts). B.6. Bug 672: Mandate "expires" in NOTIFY Changed strength of including of "expires" in a NOTIFY from "SHOULD" to "MUST" in Section 4.2.2. B.7. Bug 673: INVITE 481 response effect clarification This bug was addressed in [RFC5057]. B.8. Bug 677: SUBSCRIBE response matching text in error Fixed Section 8.2.1 to remove incorrect "...responses and..." -- explicitly pointed to SIP for transaction response handling. B.9. Bug 695: Document is not explicit about response to NOTIFY at subscription termination Added text to Section 4.4.1 indicating that the typical response to a terminal NOTIFY is a 200 (OK). B.10. Bug 696: Subscription state machine needs clarification Added state machine diagram to Section 4.1.2 with explicit handling of what to do when a SUBSCRIBE never shows up. Added definition of and handling for new Timer N to Section 4.1.2.4. Added state machine to Section 4.2.2 to reinforce text. B.11. Bug 697: Unsubscription behavior could be clarified Added text to Section 4.2.1.4 encouraging (but not requiring) full state in final NOTIFY request. Also added text to Section 4.1.2.3 warning subscribers that full state may or may not be present in the final NOTIFY. Roach Standards Track [Page 49] RFC 6665 SIP-Specific Event Notification July 2012 B.12. Bug 699: NOTIFY and SUBSCRIBE are target refresh requests Added text to both Sections 3.1 and 3.2 explicitly indicating that SUBSCRIBE and NOTIFY are target refresh methods. B.13. Bug 722: Inconsistent 423 reason phrase text Changed reason phrase to "Interval Too Brief" in Sections 4.2.1.1 and 4.2.1.4, to match 423 reason phrase in SIP [RFC3261]. B.14. Bug 741: Guidance needed on when to not include "Allow-Events" Added non-normative clarification to Section 4.4.4 regarding inclusion of "Allow-Events" in a NOTIFY for the one-and-only package supported by the notifier. B.15. Bug 744: 5xx to NOTIFY terminates a subscription, but should not Issue of subscription (usage) termination versus dialog termination is handled in [RFC5057]. The text in Section 4.2.2 has been updated to summarize the behavior described by RFC 5057, and cites it for additional detail and rationale. B.16. Bug 752: Detection of forked requests is incorrect Removed erroneous "CSeq" from list of matching criteria in Section 5.4.9. B.17. Bug 773: Reason code needs IANA registry Added Section 7.2 to create and populate IANA registry. B.18. Bug 774: Need new reason for terminating subscriptions to resources that never change Added new "invariant" reason code to Section 4.1.3 and to ABNF syntax in Section 8.4. B.19. Clarify Handling of "Route"/"Record-Route" in NOTIFY Changed text in Section 4.3 in order to mandate "Record-Route" in initial SUBSCRIBE and all NOTIFY requests, and add "MAY"-level statements for subsequent SUBSCRIBE requests. Roach Standards Track [Page 50] RFC 6665 SIP-Specific Event Notification July 2012 B.20. Eliminate Implicit Subscriptions Added text to Section 4.2.1 explaining some of the problems associated with implicit subscriptions, and added normative language prohibiting them. Removed language from Section 3.2 describing "non- SUBSCRIBE" mechanisms for creating subscriptions. Simplified language in Section 4.2.2, now that the soft-state/non-soft-state distinction is unnecessary. B.21. Deprecate Dialog Reuse Moved handling of dialog reuse and "id" handling to Section 4.5.2. It is documented only for backwards-compatibility purposes. B.22. Rationalize Dialog Creation Section 4.4.1 has been updated to specify that dialogs should be created when the NOTIFY arrives. Previously, the dialog was established by the SUBSCRIBE 200 or by the NOTIFY transaction. This was unnecessarily complicated; the newer rules are easier to implement (and result in effectively the same behavior on the wire). B.23. Refactor Behavior Sections Reorganized Section 4 to consolidate behavior along role lines (subscriber/notifier/proxy) instead of method lines. B.24. Clarify Sections That Need to Be Present in Event Packages Added sentence to Section 5 clarifying that event packages are expected to include explicit sections covering the issues discussed in this section. B.25. Make CANCEL Handling More Explicit Text in Section 4.6 now clearly calls out behavior upon receipt of a CANCEL. We also echo the "...SHOULD NOT send..." requirement from [RFC3261]. B.26. Remove "State Agent" Terminology As originally planned, we anticipated a fairly large number of event packages that would move back and forth between end-user devices and servers in the network. In practice, this has ended up not being the case. Certain events, like dialog state, are inherently hosted at end-user devices; others, like presence, are almost always hosted in the network (due to issues like composition, and the ability to deliver information when user devices are offline). Further, the Roach Standards Track [Page 51] RFC 6665 SIP-Specific Event Notification July 2012 concept of State Agents is the most misunderstood by event package authors. In my expert review of event packages, I have yet to find one that got the concept of State Agents completely correct -- and most of them start out with the concept being 100% backwards from the way RFC 3265 described it. Rather than remove the ability to perform the actions previously attributed to the widely misunderstood term "State Agent", we have simply eliminated this term. Instead, we talk about the behaviors required to create state agents (state aggregation, subscription notification) without defining a formal term to describe the servers that exhibit these behaviors. In effect, this is an editorial change to make life easier for event package authors; the actual protocol does not change as a result. The definition of "State Agent" has been removed from Section 2. Section 4.4.2 has been retooled to discuss migration of subscription in general, without calling out the specific example of state agents. Section 5.4.11 has been focused on state aggregation in particular, instead of state aggregation as an aspect of state agents. B.27. Miscellaneous Changes The following changes are relatively minor revisions to the document that resulted primarily from review of this document in the working group and IESG, rather than implementation reports. o Clarified scope of "Event" header field parameters. In RFC 3265, the scope is ambiguous, which causes problems with the registry in RFC 3968. The new text ensures that "Event" header field parameters are unique across all event packages. o Removed obsoleted language around IANA registration policies for event packages. Instead, we now cite RFC 5727, which updates RFC 3265, and is authoritative on event package registration policy. o Several editorial updates after input from working group, including proper designation of "dialog usage" rather than "dialog" where needed. o Clarified two normative statements about subscription termination by changing from plain English prose to RFC2119 language. o Removed "Table 2" expansions, per WG consensus on how SIP Table 2 is to be handled. o Removed 202 response code. Roach Standards Track [Page 52] RFC 6665 SIP-Specific Event Notification July 2012 o Clarified that "Allow-Events" does not list event template- packages. o Added clarification about proper response when the SUBSCRIBE indicates an unknown media type in its "Accept" header field. o Minor clarifications to "Route" and "Record-Route" behavior. o Added non-normative warning about the limitations of state polling. o Added information about targeting subscriptions at specific dialogs. o Added RFC 3261 to list of documents updated by this one (rather than the "2543" indicated by RFC 3265). o Clarified text in Section 3.1.1 explaining the meaning of "Expires: 0". o Changed text in definition of "probation" reason code to indicate that subscribers don't need to re-subscribe if the associated state is no longer of use to them. o Specified that the termination of a subscription due to a NOTIFY transaction failure does not require sending another NOTIFY message. o Clarified how order of template application affects the meaning of an "Event" header field value (e.g., "foo.bar.baz" is different than "foo.baz.bar"). Author's Address Adam Roach Tekelec 17210 Campbell Rd. Suite 250 Dallas, TX 75252 US EMail: adam@nostrum.com Roach Standards Track [Page 53]